Do not work port PoE Router 891

[Francisco Sanchez]

Hi

I configure router 891, it has  PoE ports but when I connecte Access-Point, iphone or Camara for Security does not work.

The configuration on port is

interface gi1

description *** HOST ***

switchport mode access

switchport access vlan 10

spanning tree portfast

Is necessary more config?

[Leo Laohoo]

Post the complete output to the following commands: 

1.  sh version; 

2.  sh inventory; and 

3.  sh power inline

[Francisco Sanchez]

Hi

Attach information

#sh inventory
NAME: "C891F-K9", DESCR: "C891F-K9 chassis, Hw Serial#: FJC1948E1EZ, Hw Revision: 1.0"
PID: C891F-K9          , VID: V01, SN: FJC1948E1EZ

NAME: "C891F Mother board on Slot 0", DESCR: "C891F Mother board"
PID: C891F-K9          , VID: V01, SN: FOC194569C5


#

********************************************************************************

#sh energywise
Module/
Interface   Role              Name                  Usage      Lvl   Imp  Type
---------   ----              ----                  -----      ---   ---  ----
            ROUTER         SJ-CPP-ATM-001-ATM_SSV15.0  (W)  10    1    parent

#

****************************************************************************

#sh ver
Cisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.4(3)M5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Tue 09-Feb-16 06:15 by prod_rel_team

ROM: System Bootstrap, Version 15.4(1r)T1, RELEASE SOFTWARE (fc1)

ROUTER uptime is 6 days, 21 hours, 43 minutes
System returned to ROM by power-on
System image file is "flash:c800-universalk9-mz.SPA.154-3.M5.bin"
Last reload type: Normal Reload
Last reload reason: power-on



This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco C891F-K9 (revision 1.0) with 488524K/35763K bytes of memory.
Processor board ID FJC1948E1EZ
1 FastEthernet interface
9 Gigabit Ethernet interfaces
1 Serial interface
1 ISDN Basic Rate interface
1 terminal line
1 Virtual Private Network (VPN) Module
DRAM configuration is 32 bits wide
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash (Read/Write)


License Info:

License UDI:

-------------------------------------------------
Device#   PID                   SN
-------------------------------------------------
*1        C891F-K9              FJC1948E1EZ     



License Information for 'c800'
    License Level: advipservices   Type: Permanent
    Next reboot license Level: advipservices


Configuration register is 0x2102

#

[Philip D'Ath · Accepted solution]

Your 891 does not have a PoE module in it.

I believe you need:

http://www.cisco.com/c/en/us/products/collateral/routers/800-series-routers/data_sheet_c78-519930.html

800-IL-PM-4 with 125W PSU

[Leo Laohoo]

No PoE Daughter card. 

[Philip D'Ath]

There are quite a few 891 models.  The 891X-24 has built in PoE, but all the other models (to the best of my knowledge) require a PoE module to be installed to "activate" the PoE ports.  Otherwise they are just normal ports.

When you order the router you can select to order it with this module pre-installed.  You can also order it afterwards and install it in the field.