FIXED: 9300-48 %FMFP-3-OBJ_DWNLD_TO_DP_FAILED: Switch 2 R0/0:

[Fulvio Ferreira]

Hello

I recently installed one issue with a C9300-48UXM - 16.12.05b and it started  to show the following log messages:

Oct 24 07:00:19.001: %FMFP-3-OBJ_DWNLD_TO_DP_FAILED: Switch 2 R0/0: fman_fp_image: WRClient 0x1fc99b8a download to DP failed
Oct 24 07:00:48.846: %FMFP-3-OBJ_DWNLD_TO_DP_FAILED: Switch 1 R0/0: fman_fp_image: WRClient 0x1fc99b8a download to DP failed
Oct 24 07:00:49.016: %FMFP-3-OBJ_DWNLD_TO_DP_FAILED: Switch 2 R0/0: fman_fp_image: WRClient 0x1fc99b8a download to DP failed

It looks like switch is trying to create/change/delete the mac-address related to this code: 0x1fc99b8a. This mac-address 08cc.6828.1c40 has been learned from Interface Te1/1/1 only:

silaclast008-dc-1ba44#sh plat soft wired-client sw 1 f0 id 0x1fc99b8a
ID : 0x1fc99b8a
MAC address : 08cc.6828.1c40
Physical interface dpidx : 0x0000003d
Authentication state : L3 Auth
VLAN ID : 0
Open Access : Yes
Client Forward : Yes
Dynamic policy template :
Client AOM Object ID : 18300436
Client AOM Object Status : Modify/delete-failed
FWD AOM Object ID : 0
FWD AOM Object Status : Pending-issue
BIND AOM Object ID : 0
BIND AOM Object Status : Pending-issue

silaclast008-dc-1ba44#sh plat soft wired-client sw 2 f0 | in Create-failed
0x10fb974c 08cc.a7ad.fdc1 Yes Yes Create-failed
0x110aae08 d477.983b.3bd2 Yes Yes Create-failed
0x12cbce93 5017.ff88.8441 Yes Yes Create-failed
0x149fac82 0004.f2e8.b156 Yes Yes Create-failed
0x183b1725 c40a.cbaf.80c1 Yes Yes Create-failed
0x1afeee20 34db.fd9c.1741 Yes Yes Create-failed
0x1d22448e c40a.cbac.9241 Yes Yes Create-failed
0x1fc99b8a 08cc.6828.1c40 Yes Yes Create-failed

silaclast008-dc-1ba44#sh mac add add 08cc.6828.1c40
Mac Address Table
-------------------------------------------

Vlan Mac Address Type Ports
---- ----------- -------- -----
2134 08cc.6828.1c40 DYNAMIC Te1/1/1
3008 08cc.6828.1c40 DYNAMIC Te1/1/1

I've already opened a TAC case and Cisco Engineer suggested to Disable “access-session monitor” on the uplinks from Uplink Interfaces, but these log messages are still happening.

Does anyone have or had this same issue?

[balaji.bandi]

that is the part of BUG  so tac suggests an alternative, if you disable it, check show access-session see any changes.

write the config and reload and test it.

if possible upgrade to any latest IOS XE and test it.

also see another BUG

[Fulvio Ferreira]

I applied no access-session monitor on both Uplink interfaces and switch stopped logging messages.

[balaji.bandi]

Glad to know it was suppressed in the logs, we mark this as resolved.(thank you for your feedback)