01-30-2012 08:05 AM - edited 03-07-2019 04:38 AM
Dear all ,
We have a new internet connection from DSL cisco router 800 Series (877).
You has been delivered it to us with Cisco Router 800 series (Ver 877), when we connect it to the PC directly it’ll work fine with the static IP.
We configured the OSPF between the Switch and the Router. and we can reach to the DSL router IP from our LAN any where.
but we can't exit from the router to the internet.
Please i need your advice
DSL router 877 ---------------> Core Switch 6509 ----> PC
Router 877 (DSL):
-----------------
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname Lotfy
!
boot-start-marker
boot-end-marker
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 0/35
pppoe-client dial-pool-number 1
!
dsl operating-mode auto
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
description $Internet$
ip address 96.25.31.81 255.255.255.248
ip nat inside!23
ip virtual-reassembly
ip tcp adjust-mss 1452
!
interface Dialer1
ip address negotiated
ip mtu 1492
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication pap chap callin
ppp chap hostname xxxxxxxxxxxxx
ppp chap password 7 xxxxxxxxxxxxxxxxxxx
ppp pap sent-username xxxxxxxxxxxxxxxxx password 7 xxxxxxxxxxxx
!
router ospf 1
log-adjacency-changes
network 96.25.31.80 0.0.0.7 area 0
default-information originate
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer1
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
access-list 23 permit 10.10.10.0 0.0.0.7
no cdp run
!
!
!
line con 0
no modem enable
line aux 0
line vty 0 4
privilege level 15
password 7 130C04
login local
!
scheduler max-task-time 5000
end
Core Switch 6509:
------------------
interface GigabitEthernet8/25
switchport
switchport access vlan 777
switchport mode access
!
!
interface Vlan777
ip address 96.25.31.82 255.255.255.248
end
!
!
interface Vlan510
description SW_to_internet
ip address 10.170.10.250 255.255.255.0
end
!
interface GigabitEthernet8/26
switchport
switchport access vlan 510
switchport mode access
!
router ospf 1
log-adjacency-changes
network 10.170.10.0 0.0.0.255 area 0
network 96.25.31.80 0.0.0.7 area 0
default-information originate
!
ip classless
ip route 0.0.0.0 0.0.0.0 96.25.31.81
===============================================
Verify:
Lotfy#ping 10.170.10.250
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.170.10.250, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
DC-BB16509#ping 96.25.31.81
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 96.25.31.81, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
DC-BB1#traceroute 4.2.2.2
Type escape sequence to abort.
Tracing the route to 4.2.2.2
1 96.25.31.81 4 msec 0 msec 0 msec
2 * * *
3 * * *
4 * * *
5 * * *
01-30-2012 08:35 AM
I see some problem wiht the NAT configuration. You have defined the inside interface and the outside interface but haven;t actually performing the NAT translations.
Also can you pls let me know the following details...
1. Which port on the switch is connected to the DSL Router?
2. Does all your PC's on the switch in the same Vlan? if not, the link connecting the switch and the rotuer should be a trunk link.
-Vijay
01-30-2012 08:54 AM
Thanks my brother for your reply.
For the first paragraph, please i need some explanation.
1. Which port on the switch is connected to the DSL Router?
as you'll see on the Switch configrations, the Inter gig 8/25 on switch is the port that connected to DSL router.
2. Does all your PC's on the switch in the same Vlan? if not, the link connecting the switch and the rotuer should be a trunk link.
i'll check it now
01-30-2012 09:05 AM
This link might help you in the NAT Translations
http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080094e77.shtml
-Vijay
01-30-2012 09:51 AM
2. Does all your PC's on the switch in the same Vlan? if not, the link connecting the switch and the rotuer should be a trunk link.
Sorry, it's not working totally , the DSL router 877 dosen't support the trunk mode
01-31-2012 01:40 AM
Dear Brother Vijay,
It's working with me now, yes it was a NAT issue.
Thanks for your support, it was very useful for me.
Thanks again.
-Mohamed
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide