ā08-02-2012 10:39 PM - edited ā03-07-2019 08:08 AM
Hi,
We have Dell M6220 blade server that server is connected to cisco 3750 switch. I am trying to configure LACP in 3750 for two port which are connected to Dell M6220 server switch. The channel-group 2 mode active commande is not taking then its showing the error protocol mismatch and if i run show int port-channel 2 command the port channel status is showing down. The Dell server switch is on simple mode. below i have attached the required details. Please help me on this.
Switch#show int port-channel 2
Port-channel2 is down, line protocol is down (notconnect)
Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto-speed, link type is auto, media type is unknown
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
Switch#
interface Port-channel2
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet1/0/21
description ****Connected to Dell Blade****
switchport trunk encapsulation dot1q
switchport mode trunk
speed 1000
duplex full
channel-group 2 mode desirable
interface GigabitEthernet1/0/38
description ****Connected to Dell Blade****
switchport trunk encapsulation dot1q
switchport mode trunk
speed 1000
duplex full
channel-group 2 mode desirable
Switch(config)#int gi1/0/21
Switch(config-if)#no channel-group 2 mode desirable
Switch(config-if)#channel-protocol lacp
Switch(config-if)#channel-group 2 mode active
Command rejected (Channel protocol mismatch for interface Gi1/0/21 in group 2): the interface can not be added to the channel group
Switch(config-if)#
Solved! Go to Solution.
ā08-02-2012 11:28 PM
you have to configure both members at the same time. With your config the first member stays on PAgP, but the second member tries to use LACP.
Switch(config)#interface range gig 1/0/21, gig 1/0/38
Switch(config-if-range)#no channel-group 2 mode desirable
Switch(config-if-range)#channel-protocol lacp
Switch(config-if-range)#channel-group 2 mode active
ā08-02-2012 11:28 PM
you have to configure both members at the same time. With your config the first member stays on PAgP, but the second member tries to use LACP.
Switch(config)#interface range gig 1/0/21, gig 1/0/38
Switch(config-if-range)#no channel-group 2 mode desirable
Switch(config-if-range)#channel-protocol lacp
Switch(config-if-range)#channel-group 2 mode active
ā08-03-2012 12:11 AM
Thank you karsten. it's working fine.
Karthik
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: