05-09-2012 04:12 AM - edited 03-07-2019 06:36 AM
I am using a switch(3560X) and a router 7606 for the given setup.
I am doing a simple simulation of attcaching a port (on 7606 router)to the switch and testing it with various speed ,duplex setting.
The switch port is in vlan 2 with ip address x.x.x.234 mask 255.255.255.0
and the attached router port has ip address x.x.x.235 mask 255.255.255.0
The problem is:
The connection is establises for duplex full,speed 1000
but it does not establish for duplex full,speed 100
and duplex half,speed 10.
The ports are 10/100/1000 Ethernet ports.
The output from 3560 is:
3560X#sh int gig 0/10
GigabitEthernet0/10 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet, address is 442b.0389.448a (bia 442b.0389.448a)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 10Mb/s, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:35:39, output 00:35:09, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
3560X#sh run int gig 0/10
Current configuration : 129 bytes
!
interface GigabitEthernet0/10
switchport access vlan 2
switchport mode access
speed 10
duplex half
end
################################################ #######################################
3560X#sh int gig 0/10
GigabitEthernet0/10 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 442b.0389.448a (bia 442b.0389.448a)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:03, output 00:00:01, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
3560X#sh run int gig 0/10
Current configuration : 131 bytes
!
interface GigabitEthernet0/10
switchport access vlan 2
switchport mode access
speed 1000
duplex full
end
And Output from the 7606 link is :
7606-A#sh run int gig 2/10
!
interface GigabitEthernet2/10
ip address 192.168.0.235 255.255.255.0
speed 10
duplex half
end
7606-A#sh int gig 2/10
GigabitEthernet2/10 is down, line protocol is down (notconnect)
Hardware is C6k 1000Mb 802.3, address is 0011.bbb1.a140 (bia 0011.bbb1.a140)
Internet address is 192.168.0.235/24
MTU 1500 bytes, BW 10000 Kbit, DLY 10 usec,
reliability 255/255, txload 0/255, rxload 0/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 10Mb/s, media type is 10/100/1000BaseT
input flow-control is off, output flow-control is off
Clock mode is auto
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:25:11, output 00:25:10, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/59/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
L2 Switched: ucast: 1619 pkt, 103616 bytes - mcast: 4238 pkt, 311393 bytes
L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes mcast
L3 out Switched: ucast: 0 pkt, 0 bytes mcast: 0 pkt, 0 bytes
##########################################################################################
7606-A#sh run int gig 2/10
Current configuration : 102 bytes
!
interface GigabitEthernet2/10
ip address 192.168.0.235 255.255.255.0
speed 1000
duplex full
end
7606-A#sh int gig 2/10
GigabitEthernet2/10 is up, line protocol is up (connected)
Hardware is C6k 1000Mb 802.3, address is 0011.bbb1.a140 (bia 0011.bbb1.a140)
Internet address is 192.168.0.235/24
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is 10/100/1000BaseT
input flow-control is off, output flow-control is off
Clock mode is auto
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:37, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/59/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 1000 bits/sec, 1 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
L2 Switched: ucast: 1656 pkt, 105984 bytes - mcast: 4679 pkt, 342779 bytes
L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes mcast
L3 out Switched: ucast: 0 pkt, 0 bytes mcast: 0 pkt, 0 bytes
Thanks
Girish
Solved! Go to Solution.
05-09-2012 04:54 AM
Thats because you are not using a crossover cable most likely . If you are using a straight thru cable the link will only come up if the port settings are set for auto/auto because the mdix feature will only work if the ports are auto. Generally leave gig ports as auto . I bet if you change the 3560 side to auto the link will come up . You can set the 3560 side as auto and restrict the speed to 100 if you want . USe the "speed auto 100" or speed auto 10" commands.
05-09-2012 04:54 AM
Thats because you are not using a crossover cable most likely . If you are using a straight thru cable the link will only come up if the port settings are set for auto/auto because the mdix feature will only work if the ports are auto. Generally leave gig ports as auto . I bet if you change the 3560 side to auto the link will come up . You can set the 3560 side as auto and restrict the speed to 100 if you want . USe the "speed auto 100" or speed auto 10" commands.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: