08-18-2009 04:48 PM - edited 03-06-2019 07:18 AM
I have a problem.
When I connect somethings to ports such as a pc, a sever, a swich and a router, their MAC address are not appear on the ports.
As a matter of course, I adjusted the speed and duplex each other.
Empty ports have the same problem without used ports.
What should I do ?
===================================================================================
RT#sh mac-address-table interface fastEthernet 13/1
Legend: * - primary entry
age - seconds since last seen
n/a - not available
vlan mac address type learn age ports
------+----------------+--------+-----+----------+--------------------------
No entries present.
RT#show interface status module 13
Port Name Status Vlan Duplex Speed Type
Fa13/1 connected 100 full 100 10/100BaseTX
====================================================================================
ã Version : s72033-entservicesk9_wan-mz.122-18.SXF8.bin
ã show module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
5 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAL08455RLA
6 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAL1115LP4P
7 2 Supervisor Engine 720 (Hot) WS-SUP720-3B SAL10478LAW
8 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAD090309SJ
9 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAD04220BGF
10 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAL082804QJ
11 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAL0812333C
12 48 48 port 10/100 mb RJ-45 ethernet WS-X6248-RJ-45 SAD040309TS
13 48 48-port 10/100 mb RJ45 WS-X6148-RJ-45 SAL0912664E
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
7 Policy Feature Card 3 WS-F6K-PFC3B SAL10478P56 2.3 Ok
7 MSFC3 Daughterboard WS-SUP720 SAL10478LGN 2.5 Ok
8 Policy Feature Card 3 WS-F6K-PFC3B SAD09030BCL 1.1 Ok
8 MSFC3 Daughterboard WS-SUP720 SAD090201ZP 2.2 Ok
08-18-2009 04:53 PM
- Are you having the same problem is you connect one of those PCs to a port on the WS-X6248-RJ-45 module?
- Under the show int f13/1, do you see an increasing input packet count? any errors?
- Is the STP state FWD, use sh spann int f13/1 ?
08-18-2009 08:31 PM
Hi, jbrenesj
I am really appreciate your help.
- Are you having the same problem is you connect one of those PCs to a port on the WS-X6248-RJ-45 module?
-> Yes, all empty(notconnect) ports except that ports is already in use by user have the same problem.
- Under the show int f13/1, do you see an increasing input packet count? any errors?
-> Input packet count and any errors are always "0".
- Is the STP state FWD, use sh spann int f13/1 ?
-> The STP state is FWD.
What do you think of this problem ?
08-18-2009 11:29 PM
I didn't mistake your question.
- Under the show int f13/1, do you see an increasing input packet count? any errors?
-> Input packet count is increasing but I don't know the packet.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide