cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
569
Views
0
Helpful
2
Replies
Highlighted
Beginner

Management port problem

Greetings;

We just got a new ASA5510 (straight out of the box). I’m new to the Cisco but feel we followed the directions. We connect to the management port and have our workstation set to get an ip via dhcp. A cat5 is connected to the management port, that goes into a hub (tested to work) and a cat5 is connected from the hub to the workstation (tested to work). Nothing else is connected. The workstation does not get an ip address. (assigns APIPA) Both the 5510 and workstation have been rebooted.

The workstation works otherwise. We have also connected both a crossover and straight through cable from the 5510 to the workstation. We have statically assigned an ip of 192.168.1.2 to the workstation and cannot ping the cisco (192.168.1.1).

Logging into the console port, everything looks okay with the management port. We have also performed a factory reset via the console. The Cisco ASA software version is 8.2.(1) Any help or recommendations would be appreciated.

Thanks

A “show conf” yields the following.

interface Management0/0

shutdown

nameif management

security-level 100

ip address 192.168.1.1 255.255.255.0

management-only

!

ftp mode passive

pager lines 24

logging asdm informational

mtu management 1500

icmp unreachable rate-limit 1 burst-size 1

asdm image disk0:/asdm-621.bin

no asdm history enable

arp timeout 14400

timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00

timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00

timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

dynamic-access-policy-record DfltAccessPolicy

http server enable

http 192.168.1.0 255.255.255.0 management

no snmp-server location

no snmp-server contact

snmp-server enable traps snmp authentication linkup linkdown coldstart

crypto ipsec security-association lifetime seconds 28800

crypto ipsec security-association lifetime kilobytes 4608000

telnet timeout 5

ssh timeout 5

console timeout 0

dhcpd address 192.168.1.2-192.168.1.254 management

dhcpd enable management

Everyone's tags (3)
1 ACCEPTED SOLUTION

Accepted Solutions
Frequent Contributor

Management port problem

The Management interface is in shutdown state. You need to activate it.

asa#conf t

asa(config)#interface management0/0

asa(config-if)#no shutdown

asa(config-if)#end

asa#ping 192.168.1.2

HTH,

Eduardo Campos

---

Posted by WebUser Eduardo Campos from Cisco Support Community App

2 REPLIES 2
Frequent Contributor

Management port problem

The Management interface is in shutdown state. You need to activate it.

asa#conf t

asa(config)#interface management0/0

asa(config-if)#no shutdown

asa(config-if)#end

asa#ping 192.168.1.2

HTH,

Eduardo Campos

---

Posted by WebUser Eduardo Campos from Cisco Support Community App

Beginner

Management port problem

Thank you, that did it. I appreciate the quick answer.

Thanks again

CreatePlease to create content
Content for Community-Ad
July's Community Spotlight Awards