MLS 3560 can't ping another MLS 3560

[newnetwork]

Hello I'd appreciate some help here. I'm new and I'm trying to to get PC0 to be able to ping PC5 is says "destination host unreachable", both under 2 different switches. I did all i can and i'm stuck. I also noticed when i try to ping the first switch to the other it's unsuccessful.  I'm not sure if this is how you attach the file but here it is. Thanks again.

here's the running config on one switch and it's pretty much the same on the other.

Switch#show running-config

Building configuration...

Current configuration : 2636 bytes

!

version 12.2(37)SE1

no service timestamps log datetime msec

no service timestamps debug datetime msec

no service password-encryption

!

hostname Switch

!

!

!

!

!

!

ip routing

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

spanning-tree mode pvst

!

!

!

!

!

!

interface FastEthernet0/1

switchport access vlan 60

switchport mode access

!

interface FastEthernet0/2

switchport access vlan 70

switchport mode access

!

interface FastEthernet0/3

switchport access vlan 80

switchport mode access

!

interface FastEthernet0/4

switchport access vlan 90

switchport mode access

!

interface FastEthernet0/5

switchport access vlan 100

switchport mode access

!

interface FastEthernet0/6

!

interface FastEthernet0/7

!

interface FastEthernet0/8

!

interface FastEthernet0/9

!

interface FastEthernet0/10

!

interface FastEthernet0/11

!

interface FastEthernet0/12

!

interface FastEthernet0/13

!

interface FastEthernet0/14

!

interface FastEthernet0/15

!

interface FastEthernet0/16

!

interface FastEthernet0/17

!

interface FastEthernet0/18

!

interface FastEthernet0/19

!

interface FastEthernet0/20

!

interface FastEthernet0/21

!

interface FastEthernet0/22

!

interface FastEthernet0/23

!

interface FastEthernet0/24

!

interface GigabitEthernet0/1

no switchport

ip address 192.168.200.2 255.255.255.252

ip access-group HOST_ICMP in

duplex auto

speed auto

!

interface GigabitEthernet0/2

!

interface Vlan1

no ip address

shutdown

!

interface Vlan60

mac-address 000a.4155.6801

ip address 192.168.60.1 255.255.255.0

!

interface Vlan70

mac-address 000a.4155.6802

ip address 192.168.70.1 255.255.255.0

!

interface Vlan80

mac-address 000a.4155.6803

ip address 192.168.80.1 255.255.255.0

!

interface Vlan90

mac-address 000a.4155.6804

ip address 192.168.90.1 255.255.255.0

!

interface Vlan100

mac-address 000a.4155.6805

ip address 192.168.100.1 255.255.255.0

!

ip classless

!

ip flow-export version 9

!

!

ip access-list extended HOST_ICMP

permit icmp host 192.168.10.10 host 192.168.60.10

permit icmp host 192.168.60.10 host 192.168.10.10

permit icmp host 192.168.20.10 host 192.168.70.10

permit icmp host 192.168.70.10 host 192.168.20.10

permit icmp host 192.168.30.10 host 192.168.80.10

permit icmp host 192.168.80.10 host 192.168.30.10

permit icmp host 192.168.40.10 host 192.168.90.10

permit icmp host 192.168.90.10 host 192.168.40.10

permit icmp host 192.168.50.100 host 192.168.100.10

permit icmp host 192.168.100.10 host 192.168.50.10

deny icmp any any

permit ip any any

permit icmp host 192.168.200.1 host 192.168.200.2

permit icmp host 192.168.200.2 host 192.168.200.1

!

!

!

!

!

!

line con 0

!

line aux 0

!

line vty 0 4

login

!

!

!

!

end

[M02@rt37 · Accepted solution]

Hello @newnetwork 

On Gi0/1 on both swithes, configure Trunk port:

interface g0/1
switchport mode trunk
switchport trunk allowed vlan 60,70,80,90,100

After, that try ping without ACL ensure that is OK. After that asjust your ACL and apply it...

[newnetwork]

I tried this on both switches and wasn't able to ping them still

[Joseph W. Doherty]

Either attach the (zipped) PT file (if PT being used) or post other switch's config.

[Joseph W. Doherty]

I'm not sure if this is how you attach the file

If it's a Packet Tracer file, you need to zip it, and then you can attach the zip file.

At to communicating between switches, if you intend to route between them, each L3 switch needs to "know" of any non directly connected networks and how to reach them.  That might be accomplished by using static route statements on both L3 switches or running a routing protocol between them.

BTW, what M02@rt37 suggests would require identical VLAN assignments and corresponding VLAN/subnet assignments to work.

[joyride_us2]

Remove the IPAddress from Gi0/1 on both switches.

[joyride_us2]

And the VLAN's on switchport mode trunk as it has been stated. Please also remove your access-group.