03-18-2021 01:49 AM
Hello
I want to recovery password for Cisco 2960 POE -24 with more tentative with press button " MODE'
but the switch go to mode normal and i can't enter mode switch :
Step 1:
Power off the switch first, then press and hold the mode button while you power on the switch again. Hold it for about 15 seconds until the SYS led is solid green, and then release it.
The switch should then give you this prompt:
switch:
This step 1 don't work !!!!??
so how i can resolved this problem that i can recovery password for switch 2960 POE
i wait a reply from expert switching .
thanks in advance
03-18-2021 02:02 AM
What messages are you seeing on Console?
Check out the link below and see if that resolve your issue:
03-18-2021 02:09 AM
@Dhikra Marghli if any of the process mentioned above doesn't work for you, then boot the switch without flash memory. Once you will see the "switch:" prompt, reinsert the flash and proceed with the password recovery procedure. Hope that will resolve your issue.
***Please rate all helpful posts***
03-18-2021 03:07 AM
thanks to reply ... so i want to know how this switch boot if you say it is not have a memort flash !!!???
i need other solution that i can recovery password
Please , i wait a reply from you
thanks in advance
03-18-2021 03:50 AM
The switch will lead to the "switch:" prompt without flash memory. once you see this. Insert the flash memory back and proceed with the password recovery procedure and then enter the "boot" command.
03-18-2021 05:06 AM
NO , because i have 4 switch 2960 poe switch layer so i can recovery password for three switch but only one switch don't work !! that why i send a request to this forum cisco !!
so I have a problem for a single switch compared to the others which are working correctly and same plateform 2960 switch layer 2
03-18-2021 02:15 AM
i try more tentative but the step 1 don't work and nothing to show for console !!!
so what do you think about recovery password for this switch 2960-POE and what i can doing !!
//////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2021.03.18 10:08:40 =~=~=~=~=~=~=~=~=~=~=~=
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
File "flash:/c2960-lanbasek9-mz.122-50.SE5/c2960-lanbasek9-mz.122-50.SE5.bin" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(50)SE5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 28-Sep-10 13:44 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x01400000
Initializing flashfs...
Using driver version 1 for media type 1
mifs[3]: 0 files, 1 directories
mifs[3]: Total bytes : 3870720
mifs[3]: Bytes used : 1024
mifs[3]: Bytes available : 3869696
mifs[3]: mifs fsck took 0 seconds.
mifs[3]: Initialization complete.
mifs[4]: 541 files, 19 directories
mifs[4]: Total bytes : 27998208
mifs[4]: Bytes used : 11917824
mifs[4]: Bytes available : 16080384
mifs[4]: mifs fsck took 1 seconds.
mifs[4]: Initialization complete.
...done Initializing flashfs.
Checking for Bootloader upgrade.. not needed
POST: CPU MIC register Tests : Begin
POST: CPU MIC register Tests : End, Status Passed
POST: PortASIC Memory Tests : Begin
POST: PortASIC Memory Tests : End, Status Passed
POST: CPU MIC interface Loopback Tests : Begin
POST: CPU MIC interface Loopback Tests : End, Status Passed
POST: PortASIC RingLoopback Tests : Begin
POST: PortASIC RingLoopback Tests : End, Status Passed
Using driver version 1 for media type 1
Base ethernet MAC Address: d0:c2:82:33:6b:80
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
mifs[2]: 0 files, 1 directories
mifs[2]: Total bytes : 3870720
mifs[2]: Bytes used : 1024
mifs[2]: Bytes available : 3869696
mifs[2]: mifs fsck took 1 seconds.
mifs[3]: 541 files, 19 directories
mifs[3]: Total bytes : 27998208
mifs[3]: Bytes used : 11917824
mifs[3]: Bytes available : 16080384
mifs[3]: mifs fsck took 7 seconds.
...done Initializing Flash.
done.
Loading "flash:/c2960-lanbasek9-mz.122-50.SE5/c2960-lanbasek9-mz.122-50.SE5.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
File "flash:/c2960-lanbasek9-mz.122-50.SE5/c2960-lanbasek9-mz.122-50.SE5.bin" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(50)SE5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 28-Sep-10 13:44 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x01400000
Initializing flashfs...
Using driver version 1 for media type 1
mifs[3]: 0 files, 1 directories
mifs[3]: Total bytes : 3870720
mifs[3]: Bytes used : 1024
mifs[3]: Bytes available : 3869696
mifs[3]: mifs fsck took 0 seconds.
mifs[3]: Initialization complete.
mifs[4]: 541 files, 19 directories
mifs[4]: Total bytes : 27998208
mifs[4]: Bytes used : 11917824
mifs[4]: Bytes available : 16080384
mifs[4]: mifs fsck took 1 seconds.
mifs[4]: Initialization complete.
...done Initializing flashfs.
Checking for Bootloader upgrade.. not needed
POST: CPU MIC register Tests : Begin
POST: CPU MIC register Tests : End, Status Passed
POST: PortASIC Memory Tests : Begin
POST: PortASIC Memory Tests : End, Status Passed
POST: CPU MIC interface Loopback Tests : Begin
POST: CPU MIC interface Loopback Tests : End, Status Passed
POST: PortASIC RingLoopback Tests : Begin
POST: PortASIC RingLoopback Tests : End, Status Passed
front_end/ (directory)
extracting front_end/fe_type_2 (78400 bytes)
extracting front_end/fe_type_3 (78400 bytes)
extracting front_end/fe_type_4 (78400 bytes)
extracting front_end/front_end_ucode_info (129 bytes)
extracting ucode_info (76 bytes)
POST: Inline Power Controller Tests : Begin
POST: Inline Power Controller Tests : End, Status Passed
POST: PortASIC CAM Subsystem Tests : Begin
POST: PortASIC CAM Subsystem Tests : End, Status Passed
POST: PortASIC Port Loopback Tests : Begin
POST: PortASIC Port Loopback Tests : End, Status Passed
Waiting for Port download...Complete
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco WS-C2960-24PC-L (PowerPC405) processor (revision G0) with 65536K bytes of memory.
Processor board ID FCQ1524Y08W
Last reset from power-on
1 Virtual Ethernet interface
24 FastEthernet interfaces
2 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
64K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : D0:C2:82:33:6B:80
Motherboard assembly number : 73-12619-04
Power supply part number : 341-0266-03
Motherboard serial number : FCQ15200KU4
Power supply serial number : DCA1517H647
Model revision number : G0
Motherboard revision number : A0
Model number : WS-C2960-24PC-L
System serial number : FCQ1524Y08W
Top Assembly Part Number : 800-32808-01
Top Assembly Revision Number : D0
Version ID : V05
CLEI Code Number : COMCS00ARB
Hardware Board Revision Number : 0x02
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 26 WS-C2960-24PC-L 12.2(50)SE5 C2960-LANBASEK9-M
Press RETURN to get started!
*Mar 1 00:00:46.355: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Mar 1 00:00:47.538: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
000003: *Mar 1 00:00:49: %SYS-6-CLOCKUPDATE: System clock has been updated from 00:00:49 UTC Mon Mar 1 1993 to 00:00:49 GMT Mon Mar 1 1993, configured from console by console.
000004: *Mar 1 00:00:49: %SYS-6-CLOCKUPDATE: System clock has been updated from 00:00:49 GMT Mon Mar 1 1993 to 00:00:49 GMT Mon Mar 1 1993, configured from console by console.
000005: *Mar 1 00:00:51: %SYS-5-CONFIG_I: Configured from memory by console
000006: *Mar 1 00:00:51: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(50)SE5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 28-Sep-10 13:44 by prod_rel_team
000007: *Mar 1 00:00:51: %SSH-5-ENABLED: SSH 1.99 has been enabled
000008: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/4, changed state to administratively down
000009: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/5, changed state to administratively down
000010: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/6, changed state to administratively down
000011: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/7, changed state to administratively down
000012: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/8, changed state to administratively down
000013: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/9, changed state to administratively down
000014: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/10, changed state to administratively down
000015: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/11, changed state to administratively down
000016: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/12, changed state to administratively down
000017: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/13, changed state to administratively down
000018: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/14, changed state to administratively down
000019: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/15, changed state to administratively down
000020: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/16, changed state to administratively down
000021: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/17, changed state to administratively down
000022: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/18, changed state to administratively down
000023: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/19, changed state to administratively down
000024: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/20, changed state to administratively down
000025: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/21, changed state to administratively down
000026: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/22, changed state to administratively down
000027: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/23, changed state to administratively down
000028: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/24, changed state to administratively down Norbert Dentressangle Logistics
User Access Verification
Username: cisco sotetel
Password:
% Login invalid
Username: sotetel
Password:
% Login invalid
Username:
Using driver version 1 for media type 1
Base ethernet MAC Address: d0:c2:82:33:6b:80
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
mifs[2]: 0 files, 1 directories
mifs[2]: Total bytes : 3870720
mifs[2]: Bytes used : 1024
mifs[2]: Bytes available : 3869696
mifs[2]: mifs fsck took 1 seconds.
mifs[3]: 541 files, 19 directories
mifs[3]: Total bytes : 27998208
mifs[3]: Bytes used : 11917824
mifs[3]: Bytes available : 16080384
mifs[3]: mifs fsck took 7 seconds.
...done Initializing Flash.
done.
Loading "flash:/c2960-lanbasek9-mz.122-50.SE5/c2960-lanbasek9-mz.122-50.SE5.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
File "flash:/c2960-lanbasek9-mz.122-50.SE5/c2960-lanbasek9-mz.122-50.SE5.bin" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(50)SE5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 28-Sep-10 13:44 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x01400000
Initializing flashfs...
Using driver version 1 for media type 1
mifs[3]: 0 files, 1 directories
mifs[3]: Total bytes : 3870720
mifs[3]: Bytes used : 1024
mifs[3]: Bytes available : 3869696
mifs[3]: mifs fsck took 0 seconds.
mifs[3]: Initialization complete.
mifs[4]: 541 files, 19 directories
mifs[4]: Total bytes : 27998208
mifs[4]: Bytes used : 11917824
mifs[4]: Bytes available : 16080384
mifs[4]: mifs fsck took 1 seconds.
mifs[4]: Initialization complete.
...done Initializing flashfs.
Checking for Bootloader upgrade.. not needed
POST: CPU MIC register Tests : Begin
POST: CPU MIC register Tests : End, Status Passed
POST: PortASIC Memory Tests : Begin
POST: PortASIC Memory Tests : End, Status Passed
POST: CPU MIC interface Loopback Tests : Begin
POST: CPU MIC interface Loopback Tests : End, Status Passed
POST: PortASIC RingLoopback Tests : Begin
POST: PortASIC RingLoopback Tests : End, Status Passed
front_end/ (directory)
extracting front_end/fe_type_2 (78400 bytes)
extracting front_end/fe_type_3 (78400 bytes)
extracting front_end/fe_type_4 (78400 bytes)
extracting front_end/front_end_ucode_info (129 bytes)
extracting ucode_info (76 bytes)
POST: Inline Power Controller Tests : Begin
POST: Inline Power Controller Tests : End, Status Passed
POST: PortASIC CAM Subsystem Tests : Begin
POST: PortASIC CAM Subsystem Tests : End, Status Passed
POST: PortASIC Port Loopback Tests : Begin
POST: PortASIC Port Loopback Tests : End, Status Passed
Waiting for Port download...Complete
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco WS-C2960-24PC-L (PowerPC405) processor (revision G0) with 65536K bytes of memory.
Processor board ID FCQ1524Y08W
Last reset from power-on
1 Virtual Ethernet interface
24 FastEthernet interfaces
2 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
64K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : D0:C2:82:33:6B:80
Motherboard assembly number : 73-12619-04
Power supply part number : 341-0266-03
Motherboard serial number : FCQ15200KU4
Power supply serial number : DCA1517H647
Model revision number : G0
Motherboard revision number : A0
Model number : WS-C2960-24PC-L
System serial number : FCQ1524Y08W
Top Assembly Part Number : 800-32808-01
Top Assembly Revision Number : D0
Version ID : V05
CLEI Code Number : COMCS00ARB
Hardware Board Revision Number : 0x02
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 26 WS-C2960-24PC-L 12.2(50)SE5 C2960-LANBASEK9-M
Press RETURN to get started!
*Mar 1 00:00:45.969: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Mar 1 00:00:47.152: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
000003: *Mar 1 00:00:49: %SYS-6-CLOCKUPDATE: System clock has been updated from 00:00:49 UTC Mon Mar 1 1993 to 00:00:49 GMT Mon Mar 1 1993, configured from console by console.
000004: *Mar 1 00:00:49: %SYS-6-CLOCKUPDATE: System clock has been updated from 00:00:49 GMT Mon Mar 1 1993 to 00:00:49 GMT Mon Mar 1 1993, co Norbert Dentressangle Logistics
User Access Verification
Username: nfigured from console by console.
000005: *Mar 1 00:00:50: %SYS-5-CONFIG_I: Configured from memory by console
000006: *Mar 1 00:00:50: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(50)SE5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 28-Sep-10 13:44 by prod_rel_team
000007: *Mar 1 00:00:50: %SSH-5-ENABLED: SSH 1.99 has been enabled
000008: *Mar 1 00:00:51: %LINK-5-CHANGED: Interface FastEthernet0/4, changed state to administratively down
000009: *Mar 1 00:00:51: %LINK-5-CHANGED: Interface FastEthernet0/5, changed state to administratively down
000010: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/6, changed state to administratively down
000011: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/7, changed state to administratively down
000012: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/8, changed state to administratively down
000013: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/9, changed state to administratively down
000014: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/10, changed state to administratively down
000015: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/11, changed state to administratively down
000016: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/12, changed state to administratively down
000017: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/13, changed state to administratively down
000018: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/14, changed state to administratively down
000019: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/15, changed state to administratively down
000020: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/16, changed state to administratively down
000021: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/17, changed state to administratively down
000022: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/18, changed state to administratively down
000023: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/19, changed state to administratively down
000024: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/20, changed state to administratively down
000025: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/21, changed state to administratively down
000026: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/22, changed state to administratively down
000027: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/23, changed state to administratively down
000028: *Mar 1 00:00:52: %LINK-5-CHANGED: Interface FastEthernet0/24, changed state to administratively down
Username:
Username:
////////////////////////////////////////////////////////////////////////////////////////
i can't do any thing !!!
i wait a solution from you and expert switch and a reply
thanks
03-18-2021 02:51 AM
@Dhikra Marghli with some IOS version I have experienced the same behaviour in past with the Mode button. I would suggest you try to boot the switch by removing the flash memory. This will break the booting process as the switch will not able to find the IOS without flash. Once you will see the "switch:" prompt, reinsert the flash and proceed with the password recovery procedure. Hope that will resolve your issue.
***Please rate all helpful posts***
03-18-2021 03:32 AM
Flip the switch to it's side so the Mode button is being facing the table -- Let gravity "hold down" the Mode button.
Power up the switch and wait for 30 seconds. Make sure the weight of the switch is pressing down on the Mode button.
Holding the Mode button down for >20 seconds will cause the switch to go into "Express Setup".
03-18-2021 03:42 AM
I try more tentative with > 30 second and i can't acces to mode switch : for switch layer 2 2960-POE-24 cisco
so what do you think about this problem and what's the solution !!
i wait a reply and thanks in adavance
03-18-2021 06:25 AM
because i have 4 switch 2960 poe switch layer so i can recovery password for three switch but only one switch don't work !! that why i send a request to this forum cisco !!
so I have a problem for a single switch compared to the others which are working correctly and same plateform 2960 switch layer 2
03-18-2021 06:34 AM
cisco WS-C2960-24PC-L (PowerPC405) processor (revision G0) with 65536K bytes of memory.
Processor board ID FCQ1524Y08W
Last reset from power-on
1 Virtual Ethernet interface
24 FastEthernet interfaces
2 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
64K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : D0:C2:82:33:6B:80
Motherboard assembly number : 73-12619-04
Power supply part number : 341-0266-03
Motherboard serial number : FCQ15200KU4
Power supply serial number : DCA1517H647
Model revision number : G0
Motherboard revision number : A0
Model number : WS-C2960-24PC-L
System serial number : FCQ1524Y08W
Top Assembly Part Number : 800-32808-01
Top Assembly Revision Number : D0
Version ID : V05
CLEI Code Number : COMCS00ARB
Hardware Board Revision Number : 0x02
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 26 WS-C2960-24PC-L 12.2(50)SE5 C2960-LANBASEK9-M
03-18-2021 07:02 AM
I need a help and this problem is not resolved..
So i wait from exert switch help me and give me the solution !!
thanks in advance
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide