Hi, You need to configure destination NAT on router to achieve the goal.   For example, 1.1.1.1 is your public ip address, Any Internet user will access the 1.1.1.1 and by using destination NAT router will translate 1.1.1.1 to your private IP address  192.168.1.119.   #ip nat inside source static <Inside local IP address> <Inside global IP address> You also can forward/specific specific ports For Example you only want to forward/open port 443 for IP 192.168.1.119   #ip nat inside source static tcp <Inside local IP address> 443 <Inside global IP address> 443        ... View more

Please go through below link, will guide you how to get console access. https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960/hardware/installation/guide/2960_hg/hgcliset.html#61241 Please go through below link, will guide you how to upgrade IOS from cli https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960x/software/15-0_2_EX/file_management/file_management/img_files.html ... View more

Hi,   What procedure did you follow to upgrade the IOS of the switch? What are you seeing when you are accessing the switch through Console? ... View more

Hi,   172.16.20.0-172.16.20.255 is not the part of your split ACL. It should be the part of split acl in order to get the route installed to Remote access VPN. ... View more

Hi,   Increase the level of debugging to see the logs on console.Like #debug crypto isakmp 25 <1-255> Specify an optional debug level (default is 1) Use packet tracer on ASA to identify that traffic is  able to traverse.  Packet-Tracer is  utility is a handy utility for diagnosing whether traffic is able to traverse through an  ASA  firewall ... View more

Hi,   What the verison of MAC OS and the Anyconnect client you are using?   If you are on 10.15 MAC OS,  Please use Anyconnect  4.6 since Anyconnect 4.6 support 64 bit OS. ... View more

Hi,   Is there anything recently changed, like configuration or any IOS upgrade downgrade? After how much time it gets reboot? Console into the router and provide the logs of the boot process. It will be good if you collect them when router is rebooting.     ... View more

Hi The virtual MAC address used with GLBP (Gateway Load Balancing Protocol) is 0007.b400.xxyy, where xx is the GLBP group number and yy is the AVF (Active Virtual Forwarder) number. It should not be an issue. Are you getting into a problem due to this? ... View more

Hi,   The issue is most probably due to time/clock mismatch. Please check time/clock on your all networking devices. Due to time/clock mismatch certificate is not getting authenticated by the web server.   Recommendation is that time/clock should be same and real-time in the network.   Further you can configure a NTP server in your network to avoid the issue.         ... View more

Hi,   You can try  #delete <File Name> #delete ? /force Force delete /recursive Recursive delete ... View more

Hi,   Here is the link which guide you for the password recovery process. Below is the default settings for serial line  • Bits per sec: 9600 • Data bits: 8 • Parity: none • Stop bits: 1 • Flow control: none   You can try changing these values or Bits per sec for the issue you are facing. ... View more

Hi,   Check that http server is enabled. Check that VPN Pool is allowed for http access.   For example 192.168.100.0/24 is the VPN Pool then http server enable http 192.168.100.0 255.255.255.0 <Source Interface> ... View more

Hi,    There is no fixed release to this bug. Although workaround is given as to Add a rule to the ACL on the WLC GUI.     ... View more

Hi,  Here is a document which will guide, How to configure fault management administration like events, alarms and notifications. https://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/3-5/admin/guide/bk_CiscoPrimeInfastructure_3_5_AdminGuide/bk_CiscoPrimeInfastructure_3_5_AdminGuide_chapter_0111.html#con_1087774 ... View more