cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1950
Views
7
Helpful
5
Replies

mpls xconnect between cisco and juniper not coming up

mustansirt
Level 1
Level 1

hi ...trying to get mpls l2 xconnect up between cisco and juniper router but unable to do so.

 

local interface: Gi0/0/0.100 up, line protocol up, Eth VLAN 100 up

  Interworking type is Ethernet

  Destination address: 2.2.2.2, VC ID: 100, VC status: down

    Last error: Local access circuit is not ready for label advertise

    Output interface: none, imposed label stack {}

    Preferred path: not configured 

    Default path: no route

    No adjacency

  Create time: 00:22:47, last status change time: 4d10h

    Last label FSM state change time: 00:02:03

  Signaling protocol: LDP, peer 2.2.2.2:0 up

    Targeted Hello: 1.1.1.1(LDP Id) -> 2.2.2.2, LDP is DOWN, no binding

    Graceful restart: not configured and not enabled

    Non stop routing: not configured and not enabled

    Status TLV support (local/remote)   : enabled/None (no remote binding

      LDP route watch                   : enabled

      Label/status state machine        : local ready, LruRnd

      Last local dataplane   status rcvd: No fault

      Last BFD dataplane     status rcvd: Not sent

      Last BFD peer monitor  status rcvd: No fault

      Last local AC  circuit status rcvd: No fault

      Last local AC  circuit status sent: DOWN(not-forwarding)

      Last local PW i/f circ status rcvd: No fault

      Last local LDP TLV     status sent: No fault

      Last remote LDP TLV    status rcvd: None (no remote binding)

      Last remote LDP ADJ    status rcvd: None (no remote binding)

    MPLS VC labels: local 16, remote unassigned

    Group ID: local 8, remote unknown

    MTU: local 9000, remote unknown

    Remote interface description:

  Sequencing: receive disabled, send disabled

  Control Word: On (configured: autosense)

  Dataplane:

    SSM segment/switch IDs: 0/0 (used), PWID: 2

  VC statistics:

    transit packet totals: receive 0, send 0

    transit byte totals:   receive 0, send 0

    transit packet drops:  receive 0, seq error 0, send 0

 

 

sh mpls ldp bindings

  lib entry: 1.1.1.1/32, rev 2

local binding:  label: imp-null

remote binding: lsr: 2.2.2.2:0, label: 299872

  lib entry: 2.2.2.2/32, rev 11

local binding:  label: 18

remote binding: lsr: 2.2.2.2:0, label: imp-null

  lib entry: 10.20.30.0/30, rev 6

local binding:  label: imp-null

  lib entry: 40.50.60.0/30, rev 8

local binding:  label: imp-null

 

5 Replies 5

Harold Ritter
Level 12
Level 12

Could you please provide the output for "show mpls ldp discovery" and "show mpls ldp nei" from the cisco side.

 

Regards,

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

Hi harold,

 

Please find the requested o/p's

 

sh mpls ldp discovery

Local LDP Identifier:

    1.1.1.1:0

    Discovery Sources:

    Interfaces:

GigabitEthernet0/1.1510 (ldp): xmit/recv

    LDP Id: 2.2.2.2:0

GigabitEthernet0/1.1511 (ldp): xmit/recv

    LDP Id: 2.2.2.2:0

    Targeted Hellos:

1.1.1.1 -> 2.2.2.2 (ldp): active, xmit

 

sh mpls ldp neighbor

    Peer LDP Ident: 2.2.2.2:0; Local LDP Ident 1.1.1.1:0

TCP connection: 2.2.2.2.54811 - 1.1.1.1.646

State: Oper; Msgs sent/rcvd: 661/564; Downstream

Up time: 01:32:50

LDP discovery sources:

  GigabitEthernet0/1.1510, Src IP addr: 40.50.60.1

  GigabitEthernet0/1.1511, Src IP addr: 10.20.30.1

        Addresses bound to peer LDP Ident:

          10.20.30.1      40.50.60.1   

Do you have an access-list on either side of the session? Would it be possible to provide the configuration from both sides?

 

Regards,

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

Thanks Harold,

 

But the issue was resolved from Juniper end. They need to explicitly add loopback0 interface for mpls ldp to advertise label for Loopback IP.

Once they did it the xconnect came UP.

I'm glad you found the solution.

 

Thanks for posting in the Cisco Community

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México
Review Cisco Networking for a $25 gift card