09-03-2013 01:31 AM - edited 03-07-2019 03:16 PM
I'v got a 3560X switch
#sh ver
Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9NPE-M), Version 15.0(2)SE2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 05-Feb-13 12:08 by prod_rel_team
ROM: Bootstrap program is C3560E boot loader
BOOTLDR: C3560E Boot Loader (C3560X-HBOOT-M) Version 12.2(53r)SE2, RELEASE SOFTWARE (fc1)
uptime is 4 days, 5 hours, 53 minutes
System returned to ROM by power-on
System restarted at 06:33:32 MSK Fri Aug 30 2013
System image file is "flash:/c3560e-universalk9npe-mz.150-2.SE2.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
License Level: ipbase
License Type: Permanent
Next reload license Level: ipbase
cisco WS-C3560X-48P (PowerPC405) processor (revision K0) with 262144K bytes of memory.
Processor board ID FDO1703H3A9
Last reset from power-on
3 Virtual Ethernet interfaces
1 FastEthernet interface
52 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 4C:4E:35:31:D1:80
Motherboard assembly number : 73-12557-08
Motherboard serial number : FDO17040946
Model revision number : K0
Motherboard revision number : A0
Model number : WS-C3560X-48P-S
Daughterboard assembly number : 800-32786-02
Daughterboard serial number : FDO17032XP4
System serial number : FDO1703H3A9
Top Assembly Part Number : 800-31328-07
Top Assembly Revision Number : B0
Version ID : V04
CLEI Code Number : COMJP00ARD
Hardware Board Revision Number : 0x04
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 54 WS-C3560X-48P 15.0(2)SE2 C3560E-UNIVERSALK9NPE-M
Configuration register is 0xF
When I try to enable pim on interface, there is no commands(ip pim sparse/dance) on inteface level
#sh run | i multi
ip multicast-routing distributed
#conf t
Enter configuration commands, one per line. End with CNTL/Z.
(config)#int vlan 84
(config-if)#ip pim ?
passive Enable PIM passive interface operation
(config-if)#ip pim
Why it happens? Thanks
09-03-2013 01:35 AM
Hi,
You are currently running the IPBASE license. You need a higher license, e.g. IPSERVICES, to run full multicast routing. Currently, your multilayer switch supports only what is called PIM Stub Routing which is a strongly scaled-down capability of PIM participation, and is suitable only for routed access layer deployments.
Best regards,
Peter
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide