01-03-2011 01:16 PM - edited 03-06-2019 02:48 PM
If I have redundant SUP V and my netflow is on the "stand-by" sup, is it possible to issue ip route-cache flow command. Here is sh ver and sh mod
EMHS-4510-244.1#sh ver
Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12
.2(25)EWA4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Fri 23-Sep-05 13:31 by ssearch
Image text-base: 0x10000000, data-base: 0x114DFF08
ROM: 12.2(20r)EW1
Dagobah Revision 226, Swamp Revision 34
EMHS-4510-244.1 uptime is 4 weeks, 3 days, 2 hours, 34 minutes
Uptime for this control processor is 4 weeks, 3 days, 2 hours, 35 minutes
System returned to ROM by power-on
System image file is "bootflash:"
cisco WS-C4510R (MPC8245) processor (revision 4) with 524288K bytes of memory.
Processor board ID FOX101801F3
MPC8245 CPU at 400Mhz, Supervisor V
Last reset from PowerUp
18 Virtual Ethernet interfaces
124 Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.
Configuration register is 0x2101
EMHS-4510-244.1#
EMHS-4510-244.1# sh mod
Chassis Type : WS-C4510R
Power consumed by backplane : 40 Watts
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 2 Supervisor V 1000BaseX (GBIC) WS-X4516 JAE10275WT1
2 2 Supervisor V 1000BaseX (GBIC) WS-X4516 JAE10275WWQ
3 6 1000BaseX (GBIC) WS-X4306-GB JAE1026583J
4 6 1000BaseX (GBIC) WS-X4306-GB JAE10265825
5 6 1000BaseX (GBIC) WS-X4306-GB JAE102655LE
6 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAE10202ERW
7 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAE10244DA1
8 6 1000BaseX (GBIC) WS-X4306-GB JAE1123KT0N
M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 0018.1955.f480 to 0018.1955.f481 4.0 12.2(20r)EW1 12.2(25)EWA4, Ok
2 0018.1955.f482 to 0018.1955.f483 4.0 12.2(20r)EW1 12.2(25)EWA4 Ok
3 0016.9de2.bf0e to 0016.9de2.bf13 4.1 Ok
4 0016.9de2.bf44 to 0016.9de2.bf49 4.1 Ok
5 0013.c323.4534 to 0013.c323.4539 4.1 Ok
6 0017.e0da.fbf0 to 0017.e0da.fc1f 2.2 Ok
7 0018.18a9.fb20 to 0018.18a9.fb4f 2.2 Ok
8 000e.83a1.c590 to 000e.83a1.c595 4.3 Ok
Mod Redundancy role Redundancy mode Redundancy status
----+-------------------+-------------------+-------------------
1 Standby Supervisor SSO Standby hot
2 Active Supervisor SSO Active
Mod Submodule Model Serial No. Hw Status
----+-----------------------+-----------------+------------+----+---------
1 Netflow Services Card WS-F4531 JAE1229PDFO 2.2 Ok
System Failures:
----------------
Power Supply: bad/off (see 'show power')
EMHS-4510-244.1#
01-03-2011 01:29 PM
You should be able to type the command but I don't think it will show any flows as the active sup (the one processing your packets) doesn't have the netflow card. Do a force switchover if you want to use netflow or just purchase a card for the active sup.
01-05-2011 06:59 AM
Hi Edison,
Firstly, I can not type the command. I was told by another source that this is because we don't have a netflow card on the redundant (and ACTIVE) sup engine. Can you verify that this is true?
Additionally, in performing a force switch over, will we drop packets? Does this reload the Sup? Where is there a good reference of force switch over? Thanks in advance.....
01-10-2011 09:11 PM
Firstly, I can not type the command. I was told by another source that this is because we don't have a netflow card on the redundant (and ACTIVE) sup engine. Can you verify that this is true?
I don't have the hardware to verify this but I'm pretty sure if the brain of the switch (the active sup) has the feature card, the command should be available.
I highly recommend having the feature card on both Sups, in case the active fails - the NetFlow related commands will be invalid on the redundant Sup.
Additionally, in performing a force switch over, will we drop packets? Does this reload the Sup? Where is there a good reference of force switch over? Thanks in advance.....
Please refer to the documentation:
While packets shouldn't be dropped during the switchover, I recommend doing so during a maintenance window
03-05-2011 11:13 PM
Hi,
I do beleive that the recommended NetFlow software requirements for the 4510R sup V is IOS 12.2(25)SG or later. Each sup will also need the NetFlow cards for stateful switch over.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide