- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-04-2019 09:15 AM
Hi All
I am trying to setup netflow however the commands are not working. Can someone advise on what may be the problem?
SW01#show privilege
Current privilege level is 15
TOP-CIS-LAN-SW01#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SW01(config)#flow ?
% Unrecognized command
SW01(config)#flow
% Incomplete command.
SW01(config)#ip flo?
% Unrecognized command
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
* 1 56 WS-C3850-48T 03.06.06E cat3k_caa-universalk9 INSTALL
2 56 WS-C3850-48P 03.06.06E cat3k_caa-universalk9 INSTALL
3 56 WS-C3850-48P 03.06.06E cat3k_caa-universalk9 INSTALL
4 56 WS-C3850-48T 03.06.06E cat3k_caa-universalk9 INSTALL
5 56 WS-C3850-48P 03.06.06E cat3k_caa-universalk9 INSTALL
6 56 WS-C3850-48P 03.06.06E cat3k_caa-universalk9 INSTALL
7 56 WS-C3850-48P 03.06.06E cat3k_caa-universalk9 INSTALL
8 56 WS-C3850-48P 03.06.06E cat3k_caa-universalk9 INSTALL
9 32 WS-C3850-24P 03.06.06E cat3k_caa-universalk9 INSTALL
License Level: Lanbase
License Type: Permanent
Solved! Go to Solution.
- Labels:
-
LAN Switching
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-04-2019 10:11 AM
Hello Brian,
I am afraid that you have a licensing issue:
>> License Level: Lanbase
You probably need an higher level license like IPBase to support netflow
Hope to help
Giuseppe
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-04-2019 10:11 AM
Hello Brian,
I am afraid that you have a licensing issue:
>> License Level: Lanbase
You probably need an higher level license like IPBase to support netflow
Hope to help
Giuseppe
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-04-2019 10:51 AM
I have other switches with the same license level that are working:
SW02(config)#flow ?
exporter Define a Flow Exporter
monitor Define a Flow Monitor
record Define a Flow Record
License Level: Lanbase
License Type: Permanent
Next reload license Level: Lanbase
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
1 32 WS-C3850-24T 03.02.02.SE cat3k_caa-universalk9 INSTALL
2 32 WS-C3850-24T 03.02.02.SE cat3k_caa-universalk9 INSTALL
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-05-2019 02:06 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-05-2019 05:13 AM
Looks like a licensing issue after all. Cisco probably didn't remove the commands in the old IOS initially when it was released.
