06-04-2010 06:17 AM - edited 03-06-2019 11:25 AM
New blades (module 11 and 13) are recognized by the system, but not powering on. See Below:
trd651301#sho mod
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL1114KR8C
2 5 Communication Media Module WS-SVC-CMM SAD110204XX
3 48 48-port 10/100 RJ45 Ethernet Module WS-X6148A-45AF SAL1115LCJL
4 48 48-port 10/100 RJ45 Ethernet Module WS-X6148A-45AF SAL1115LN2U
5 48 48-port 10/100 RJ45 Ethernet Module WS-X6148A-45AF SAL1115LCJN
6 48 48-port 10/100 RJ45 Ethernet Module WS-X6148A-45AF SAL1115LMDC
7 9 Supervisor Engine 32 8GE (Active) WS-SUP32-GE-3B SAL1120P0E3
8 0 Unknown (Other) Unknown Unknown
9 48 48-port 10/100 RJ45 Ethernet Module WS-X6148A-45AF SAL1115LMG3
10 48 48-port 10/100 RJ45 Ethernet Module WS-X6148A-45AF SAL1115LCL4
11 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1419HJJ8
13 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1419HJKY
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 001b.2a8b.40c8 to 001b.2a8b.40f7 11.1 7.2(1) t_whit21@1.0 Ok
2 0019.e828.f91e to 0019.e828.f927 2.9 12.4(16), 12.4(16), Ok
3 001b.54ae.5a60 to 001b.54ae.5a8f 4.3 8.4(1) t_whit21@1.0 Ok
4 001b.5480.7d60 to 001b.5480.7d8f 4.3 8.4(1) t_whit21@1.0 Ok
5 001b.54ae.4f20 to 001b.54ae.4f4f 4.3 8.4(1) t_whit21@1.0 Ok
6 001b.5480.8060 to 001b.5480.808f 4.3 8.4(1) t_whit21@1.0 Ok
7 001a.6d1a.e842 to 001a.6d1a.e84d 4.5 12.2(18r)SX2 12.2(33)SXI1 Ok
8 0000.0000.0000 to 0000.0000.0000 0.0 Unknown Unknown Unknown
9 001b.5480.79d0 to 001b.5480.79ff 4.3 8.4(1) t_whit21@1.0 Ok
10 001b.5480.3710 to 001b.5480.373f 4.3 8.4(1) t_whit21@1.0 Ok
11 5475.d06f.e4c0 to 5475.d06f.e4ef 3.4 Unknown Unknown PwrDown
13 5475.d06f.e2b0 to 5475.d06f.e2df 3.4 Unknown Unknown PwrDown
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
2/1 6-Port T1 Interface WS-SVC-CMM-6T1 SAD110406LD 2.3 Ok
2/2 6-Port T1 Interface WS-SVC-CMM-6T1 SAD11070148 2.3 Ok
3 IEEE Voice Daughter Card WS-F6K-48-AF SAL1114KV5L 2.3 Ok
4 IEEE Voice Daughter Card WS-F6K-48-AF SAL1115LN4F 2.3 Ok
5 IEEE Voice Daughter Card WS-F6K-48-AF SAL1115LB6C 2.3 Ok
6 IEEE Voice Daughter Card WS-F6K-48-AF SAL1115L7H8 2.3 Ok
7 Policy Feature Card 3 WS-F6K-PFC3B SAL1120P0GU 2.3 Ok
7 Cat6k MSFC 2A daughterboard WS-F6K-MSFC2A SAL1120P028 4.0 Ok
9 IEEE Voice Daughter Card WS-F6K-48-AF SAL1115LN68 2.3 Ok
10 IEEE Voice Daughter Card WS-F6K-48-AF SAL1115LB65 2.3 Ok
11 Centralized Forwarding Card WS-F6700-CFC SAL1417GJWC 4.1 PwrDown
13 Centralized Forwarding Card WS-F6700-CFC SAL1417GHWK 4.1 PwrDown
Mod Online Diag Status
---- -------------------
1 Bypass
2 Bypass
3 Bypass
4 Bypass
5 Bypass
6 Bypass
7 Bypass
8 Not Applicable
9 Bypass
10 Bypass
11 Not Applicable
13 Not Applicable
trd651301#sho power status module 11
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
11 WS-X6748-GE-TX 325.50 7.75 - - on off (Fabric required)
trd651301#sho power status module 13
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
13 WS-X6748-GE-TX 325.50 7.75 - - on off (Fabric required)
trd651301#
Any ideas?
attached is the sho ver.
Solved! Go to Solution.
06-04-2010 06:49 AM
Hello Ryan,
these 6748 linecards are supported only when using sup720 you have a sup32!
>> 7 9 Supervisor Engine 32 8GE (Active) WS-SUP32-GE-3B SAL1120P0E3
so they are powered off because they cannot talk to other modules without a sup720 with its built-in 720 Gbps switching fabric
remove them from this chassis you cannot use them in it unless you change supervisor
sup32 has only the 32 Gbps shared bus no switching fabric
see
Hope to help
Giuseppe
06-04-2010 06:50 AM
06-04-2010 06:36 AM
Hi Ryan,
Do you have a big enough power supply to light up all the module?
HTH
Reza
06-04-2010 06:49 AM
Hello Ryan,
these 6748 linecards are supported only when using sup720 you have a sup32!
>> 7 9 Supervisor Engine 32 8GE (Active) WS-SUP32-GE-3B SAL1120P0E3
so they are powered off because they cannot talk to other modules without a sup720 with its built-in 720 Gbps switching fabric
remove them from this chassis you cannot use them in it unless you change supervisor
sup32 has only the 32 Gbps shared bus no switching fabric
see
Hope to help
Giuseppe
06-04-2010 06:50 AM
It's because you have a Sup32.
WS-X6748-GE-TX requires Sup720.
06-04-2010 07:05 AM
Thanks for the ratings.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide