All
i am trying to enable policy based routing feature on Nexus switch, but i am getting error, command not available.
show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Documents: http://www.cisco.com/en/US/products/ps9372/tsd_products_support_series_home.html
Copyright (c) 2002-2013, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software are covered under the GNU Public
License. A copy of the license is available at
http://www.gnu.org/licenses/gpl.html.
Software
BIOS: version 3.6.0
loader: version N/A
kickstart: version 6.0(2)N1(2a)
system: version 6.0(2)N1(2a)
Power Sequencer Firmware:
Module 1: version v1.0
Module 3: version v5.0
Microcontroller Firmware: version v1.2.0.1
SFP uC: Module 1: v1.0.0.0
QSFP uC: Module not detected
BIOS compile time: 05/09/2012
kickstart image file is: bootflash:///n5000-uk9-kickstart.6.0.2.N1.2a.bin
kickstart compile time: 5/20/2013 9:00:00 [05/20/2013 17:43:34]
system image file is: bootflash:///n5000-uk9.6.0.2.N1.2a.bin
system compile time: 5/20/2013 9:00:00 [05/20/2013 20:18:17]
Hardware
cisco Nexus5548 Chassis ("O2 32X10GE/Modular Universal Platform Supervisor")
Intel(R) Xeon(R) CPU with 8262944 kB of memory.
Processor Board ID FOC17165AVX
Device name: NFRA1L3CORE1
bootflash: 2007040 kB
Kernel uptime is 468 day(s), 3 hour(s), 45 minute(s), 44 second(s)
Last reset
Reason: Unknown
System version: 6.0(2)N1(2a)
Service:
plugin
Core Plugin, Ethernet Plugin
show feature
Feature Name Instance State
-------------------- -------- --------
Flexlink 1 disabled
amt 1 disabled
bgp 1 enabled
cts 1 disabled
dhcp 1 enabled
dot1x 1 disabled
eigrp 1 disabled
eigrp 2 disabled
eigrp 3 disabled
eigrp 4 disabled
eth_port_sec 1 disabled
fcoe 1 disabled
fcoe-npv 1 disabled
fex 1 enabled
glbp 1 disabled
hsrp_engine 1 enabled
interface-vlan 1 enabled
isis 1 disabled
isis 2 disabled
isis 3 disabled
isis 4 disabled
lacp 1 enabled
ldap 1 disabled
lldp 1 enabled
msdp 1 disabled
oim 1 disabled
ospf 1 enabled
ospf 2 enabled (not-running)
ospf 3 enabled (not-running)
ospf 4 enabled (not-running)
ospfv3 1 disabled
ospfv3 2 disabled
ospfv3 3 disabled
ospfv3 4 disabled
pbr 1 disabled
pim 1 disabled
poe 1 disabled
private-vlan 1 disabled
privilege 1 disabled
NFRA1L3CORE1# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
NFRA1L3CORE1(config)# feature ?
bgp Enable/Disable Border Gateway Protocol (BGP)
cts Enable/Disable CTS
dhcp Enable/Disable DHCP Snooping
dot1x Enable/Disable dot1x
eigrp Enable/Disable Enhanced Interior Gateway Routing Protocol (EIGRP)
fcoe Enable/Disable FCoE/FC feature
fcoe-npv Enable/Disable FCoE NPV feature
fex Enable/Disable FEX
flexlink Enable/Disable Flexlink
hsrp Enable/Disable Hot Standby Router Protocol (HSRP)
http-server Enable/Disable http-server
interface-vlan Enable/Disable interface vlan
lacp Enable/Disable LACP
msdp Enable/Disable Multicast Source Discovery Protocol (MSDP)
ntp Enable/Disable NTP
ospf Enable/Disable Open Shortest Path First Protocol (OSPF)
ospfv3 Enable/Disable Open Shortest Path First Version 3 Protocol (OSPFv3)
pim Enable/Disable Protocol Independent Multicast (PIM)
port-security Enable/Disable port-security
private-vlan Enable/Disable private-vlan
privilege Enable/Disable IOS type privilege level support
ptp Enable/Disable PTP
rip Enable/Disable Routing Information Protocol (RIP)
scp-server Enable/Disable SCP server
sftp-server Enable/Disable SFTP server
ssh Enable/Disable ssh
tacacs+ Enable/Disable tacacs+
telnet Enable/Disable telnet
udld Enable/Disable UDLD
vpc Enable/Disable VPC (Virtual Port Channel)
vrrp Enable/Disable Virtual Router Redundancy Protocol (VRRP)
vtp Enable/Disable Vlan Trunking Protocol (VTP)
NFRA1L3CORE1(config)# fea
feature feature-set
NFRA1L3CORE1(config)# feature pbr
^
Can someone suggest me what can be the issue? Switch have LAN_ENTERPRISE_SERVICES_PKG license.
Regards
Rashpal Singh
.jpg "Hall of Fame Master"){kind=icon}
