05-20-2012 09:57 AM - edited 03-07-2019 06:48 AM
Hi All,
I am trying to connect poe device on WS-X6748-SFP port, it showing inline power not supported.
It means this module not support POE or I have to enable something...
Appreciate if any one can help on this.. Thanks!
ABCD#sh power inline gi1/4/8
Interface Gi1/4/8: inline power not supported
ABCD#show power
system power redundancy mode = redundant
system power total = 5771.64 Watts (137.42 Amps @ 42V)
system power used = 1456.98 Watts (34.69 Amps @ 42V)
system power available = 4314.66 Watts (102.73 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-6000W 5771.64 137.42 OK OK on
2 WS-CAC-6000W 5771.64 137.42 OK OK on
Pwr-Allocated Oper
Fan Type Watts A @42V State
---- ------------------ ------- ------ -----
1 WS-C6509-E-FAN 210.00 5.00 OK
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
2 WS-SVC-FWM-1 171.78 4.09 171.78 4.09 on on
4 WS-X6748-SFP 292.74 6.97 292.74 6.97 on on
5 VS-S720-10G 338.10 8.05 338.10 8.05 on on
6 WS-X6708-10GE 444.36 10.58 444.36 10.58 on on
system auxiliary power mode = off
system auxiliary power redundancy operationally = non-redundant
system primary connector power limit = 10920.00 Watts (260.00 Amps @ 42V)
system auxiliary connector power limit = 10500.00 Watts (250.00 Amps @ 42V)
system primary power used = 1456.98 Watts (34.69 Amps @ 42V)
system auxiliary power used = 0 WattTENANT-CORE-SWITCH#show power
system power redundancy mode = redundant
system power total = 5771.64 Watts (137.42 Amps @ 42V)
system power used = 1456.98 Watts (34.69 Amps @ 42V)
system power available = 4314.66 Watts (102.73 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-6000W 5771.64 137.42 OK OK on
2 WS-CAC-6000W 5771.64 137.42 OK OK on
Pwr-Allocated Oper
Fan Type Watts A @42V State
---- ------------------ ------- ------ -----
1 WS-C6509-E-FAN 210.00 5.00 OK
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
2 WS-SVC-FWM-1 171.78 4.09 171.78 4.09 on on
4 WS-X6748-SFP 292.74 6.97 292.74 6.97 on on
5 VS-S720-10G 338.10 8.05 338.10 8.05 on on
6 WS-X6708-10GE 444.36 10.58 444.36 10.58 on on
system auxiliary power mode = off
system auxiliary power redundancy operationally = non-redundant
system primary connector power limit = 10920.00 Watts (260.00 Amps @ 42V)
system auxiliary connector power limit = 10500.00 Watts (250.00 Amps @ 42V)
system primary power used = 1456.98 Watts (34.69 Amps @ 42V)
system auxiliary power used = 0 Watt
Solved! Go to Solution.
05-20-2012 10:20 AM
Hi,
Fiber modules (SFP) do not support POE. Only copper modules do.
for example this card support POE:
WS-X6548-GE-45AF
Have a look at table-7 in this link:
HTH
05-20-2012 10:20 AM
Hi,
Fiber modules (SFP) do not support POE. Only copper modules do.
for example this card support POE:
WS-X6548-GE-45AF
Have a look at table-7 in this link:
HTH
05-20-2012 10:38 AM
I was trying to connect Cisco Access Point using GLCT to the port..
Thanks for your valuable information.
05-20-2012 10:44 AM
Sorry, it will not work with GLC-T.
Please rate and close the threat, so others can benefit from it.
05-20-2012 03:12 PM
I was trying to connect Cisco Access Point using GLCT to the port..
Won't work because a GLC-T SFP module doesn't support PoE either.
The only way to get the WAP working is to either use a power injector or a power pack/power brick.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide