10-14-2019 08:36 AM
Hi Guys,
Got a strange issue between our core switch SX550-48 to our edge switch SX350-48. We use 4 copper links between the edge and core in a single port channel. The core switch shows all physical links up but the edge side is down. Not sure what is going on here but we have the same config on all of our switches stack across the site which works fine.
Edge side
Load balancing: src-dst-mac.
Gathering information...
Channel Ports
------- -----
Po1 Active: te2/0/1-2 Non-candidate: te1/0/1-2
te1/0/1 10G-Combo-C -- -- -- -- Down -- --
te1/0/2 10G-Combo-C -- -- -- -- Down -- --
te2/0/1 10G-Combo-C Full 1000 Enabled Off Up Disabled Off
te2/0/2 10G-Combo-C Full 1000 Enabled Off Up Disabled Off
Core side:
Load balancing: src-dst-mac.
Gathering information......
Channel Ports
------- -----
Po4 Active: gi1/0/10,gi2/0/10 Non-candidate: gi1/0/9,gi2/0/9
gi1/0/9 1G-Copper Full 1000 Enabled Off Up Disabled Off
gi1/0/10 1G-Copper Full 1000 Enabled Off Up Disabled On
gi2/0/9 1G-Copper Full 1000 Enabled Off Up Disabled Off
gi2/0/10 1G-Copper Full 1000 Enabled Off Up Disabled On
Thanks a lot!
Jonathan
10-14-2019 10:34 AM
Hi,
Can you check that non-candidate ports are getting suspended or not?
If Ports are in suspended mode then restart that remote switch. I am facing same issue with 550X from the last 1 year. No solution found yet.
10-15-2019 02:57 AM
Hey Keepak,
Thanks for the reply. Can confirm that the port's are not suspended - very strange one. Tried changing the cables too incase of a physical issue.
Jonathan
10-14-2019 11:28 AM
Can you post the config of the physical and pc interfaces from both switches please?
10-15-2019 03:06 AM
Hi Paul,
Thanks for the replay. Please see below.
Edge switch
interface TenGigabitEthernet1/0/1
lacp port-priority 1000
no spanning-tree portfast
spanning-tree link-type point-to-point
channel-group 1 mode auto
switchport mode trunk
lldp med disable
!
interface TenGigabitEthernet1/0/2
lacp port-priority 1000
no spanning-tree portfast
spanning-tree link-type point-to-point
channel-group 1 mode auto
switchport mode trunk
lldp med disable
interface TenGigabitEthernet2/0/1
lacp port-priority 2000
no spanning-tree portfast
spanning-tree link-type point-to-point
channel-group 1 mode auto
switchport mode trunk
lldp med disable
!
interface TenGigabitEthernet2/0/2
lacp port-priority 2000
no spanning-tree portfast
spanning-tree link-type point-to-point
channel-group 1 mode auto
switchport mode trunk
lldp med disable
interface Port-Channel1
no spanning-tree portfast
spanning-tree link-type point-to-point
switchport mode trunk
Core side
interface GigabitEthernet1/0/9
description ST4-SW1-49
lacp port-priority 1000
spanning-tree link-type point-to-point
channel-group 4 mode auto
switchport mode trunk
!
interface GigabitEthernet1/0/10
description ST4-SW2-49
lacp port-priority 1000
spanning-tree link-type point-to-point
channel-group 4 mode auto
switchport mode trunk
interface GigabitEthernet2/0/9
description ST4-SW1-50
lacp port-priority 2000
spanning-tree link-type point-to-point
channel-group 4 mode auto
switchport mode trunk
!
interface GigabitEthernet2/0/10
description ST4-SW2-50
lacp port-priority 2000
spanning-tree link-type point-to-point
channel-group 4 mode auto
switchport mode trunk
interface Port-Channel4
loopback-detection enable
description Stack4
spanning-tree link-type point-to-point
switchport mode trunk
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide