router 7604 is not accepting some of class-map commands!!!!

[Dr.X]

hi ,

my router is 7604 , with ios

bootdisk:c7600s3223-adventerprisek9-mz.152-1.S.bin

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

i have some commands in class maps is not being accepted from router , i mean i cant type

these config was workign ok on 7200

with ios  advance ip service and every thing was ok ,

my question is  do i need to upgarde my current ios on 7600 to access these QOS commands ??

is there any solutions ??

the followign commadns is not being accepted by the router

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

class-map match-any WEB_SENSTIVE

match protocol http mime "text*"

match protocol http mime "image*"

match protocol http mime "application/x-javascript"

match protocol http mime "application/javascript"

match protocol http mime "application/xml"

class-map match-all ICMP

match protocol icmp

class-map match-all P2P

match protocol bittorrent

match protocol kazaa2

match protocol fasttrack

match protocol gnutella

match protocol edonkey

class-map match-all rrr

match access-group name rrr

class-map match-all BUS

match access-group name BUS

class-map match-all VIP

match access-group name VIP

class-map match-any VIDEO

match protocol http mime "video*"

class-map match-any MANAGMENT

match protocol snmp

match protocol telnet

match protocol ssh

match protocol ospf

match protocol bgp

match protocol dns

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

[Giuseppe Larosa]

Hello Ahmed,

the problem is likely caused by the match protocol statements, because they require support for NBAR and NBAR is not supported on all C7600-C6500 supervisors.

It is not a question of IOS image, but rather of different features supported at platform level and it is determined by supervisor type.

only sup32 PISA version supports NBAR

see

http://www.cisco.com/en/US/prod/collateral/modules/ps2797/ps7209/product_data_sheet0900aecd805a6b87_ps708_Products_Data_Sheet.html

compare with sup32 datasheet

http://www.cisco.com/en/US/prod/collateral/modules/ps2797/ps5972/product_data_sheet0900aecd801c5cab_ps708_Products_Data_Sheet.html

check the supervisor type with show module

Hope to help

Giuseppe

[Dr.X]

hi ,

thanks soo much for ur reply

===========

i read the tables and seems that my module which is    cant handle these   QOS commands ,

but i think that if i bought the module pisa  32 , it will sove my problem .

i read from table that pisa 32 chasis requirement:

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

All Cisco Catalyst 6500 Series chassis with fan tray 2 or E-Series fan tray and 2500W power supplies or above

%%%%%%%%%%%%

does that speech mean that it is supprted to 7604 ??? does this module 

Supervisor Engine 32 PISA

being   supported by 7604 ???

regards

[Giuseppe Larosa · Accepted solution]

Hello Ahmed,

sup32 PISA is not listed among possible supervisors in C7604 chassis datasheet

http://www.cisco.com/en/US/prod/collateral/routers/ps368/ps6316/product_data_sheet0900aecd8027cc3e.html

>> Supervisor support: Cisco Catalyst 6500 Supervisor  Engine 32 (WS-SUP32-GE-3B and WS-SUP32-10GE-3B), Cisco Catalyst 6500  Supervisor Engine 720 (WS-SUP720-3B and WS-SUP720-3BXL), and the new  Cisco Route Switch Processor 720 (RSP720-3C and RSP720-3CXL)

I'm sorry this may be bad news for you

Hope to help

Giuseppe