Hello all,
I have a NAS with 4 sfp+ port in it and i configure trunking with 802.3ad dynamic mode, and then i configure vlan on that port. i connect those 4 sfp+ to unmanaged switch and from that i use rj45 to connect to my switch which is sg350. in my sg350 then i config LACP with this config and saw this error
switch(config)#int ra g13-16
switch(config-if-range)#channel-group 2 mode auto
switch(config-if-range)#interface port-channel 2
switch(config-if)#swi mode trunk
switch(config-if)#swi tru native vlan 99
switch(config-if)#sh
switch(config-if)#15-Dec-2020 13:33:54 %TRUNK-W-PORTREMOVED: Port gi13 removed from Po2
15-Dec-2020 13:33:54 %LINK-W-Down: gi13
15-Dec-2020 13:33:54 %LINK-W-Down: gi14
15-Dec-2020 13:33:54 %LINK-W-Down: gi15
15-Dec-2020 13:33:54 %LINK-W-Down: gi16
15-Dec-2020 13:33:54 %LINK-W-Down: Po2
switch(config-if)#no sh
switch(config-if)#15-Dec-2020 13:34:05 %LINK-I-Up: gi13
15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpSingleNeighbour: Single LLDP neighbour on port gi13 - EEE operational state can be TRUE
15-Dec-2020 13:34:05 %LINK-I-Up: gi16
15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpSingleNeighbour: Single LLDP neighbour on port gi16 - EEE operational state can be TRUE
15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpSingleNeighbour: Single LLDP neighbour on port gi14 - EEE operational state can be TRUE
15-Dec-2020 13:34:05 %LINK-I-Up: gi14
15-Dec-2020 13:34:05 %LINK-I-Up: gi15
15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpSingleNeighbour: Single LLDP neighbour on port gi15 - EEE operational state can be TRUE
15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpMultiNeighbours: Multiple LLDP neighbours on port gi13 - EEE operational state is FALSE
15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpMultiNeighbours: Multiple LLDP neighbours on port gi14 - EEE operational state is FALSE
15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpMultiNeighbours: Multiple LLDP neighbours on port gi15 - EEE operational state is FALSE
15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpMultiNeighbours: Multiple LLDP neighbours on port gi16 - EEE operational state is FALSE
15-Dec-2020 13:34:10 %TRUNK-I-PORTADDED: Port gi13 added to Po2
15-Dec-2020 13:34:10 %LINK-I-Up: Po2
15-Dec-2020 13:34:10 %STP-W-PORTSTATUS: Po2: STP status Forwarding
15-Dec-2020 13:34:11 %STP-I-EDGEPORT: Attention: port Po2 from which the bpdu was received is configured as Fast Port
15-Dec-2020 13:34:11 %STP-W-PORTSTATUS: Po2: STP status Blocking
15-Dec-2020 13:34:11 %STP-W-LOOPBACKDET: Po2: STP Loopback Detection.
i tried disable and enable spanning-tree portfast on that port with no luck.
i think i miss something here, can someone help?
Thank you.
