12-15-2020 04:00 AM
Hello all,
I have a NAS with 4 sfp+ port in it and i configure trunking with 802.3ad dynamic mode, and then i configure vlan on that port. i connect those 4 sfp+ to unmanaged switch and from that i use rj45 to connect to my switch which is sg350. in my sg350 then i config LACP with this config and saw this error
switch(config)#int ra g13-16 switch(config-if-range)#channel-group 2 mode auto switch(config-if-range)#interface port-channel 2 switch(config-if)#swi mode trunk switch(config-if)#swi tru native vlan 99 switch(config-if)#sh switch(config-if)#15-Dec-2020 13:33:54 %TRUNK-W-PORTREMOVED: Port gi13 removed from Po2 15-Dec-2020 13:33:54 %LINK-W-Down: gi13 15-Dec-2020 13:33:54 %LINK-W-Down: gi14 15-Dec-2020 13:33:54 %LINK-W-Down: gi15 15-Dec-2020 13:33:54 %LINK-W-Down: gi16 15-Dec-2020 13:33:54 %LINK-W-Down: Po2 switch(config-if)#no sh switch(config-if)#15-Dec-2020 13:34:05 %LINK-I-Up: gi13 15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpSingleNeighbour: Single LLDP neighbour on port gi13 - EEE operational state can be TRUE 15-Dec-2020 13:34:05 %LINK-I-Up: gi16 15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpSingleNeighbour: Single LLDP neighbour on port gi16 - EEE operational state can be TRUE 15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpSingleNeighbour: Single LLDP neighbour on port gi14 - EEE operational state can be TRUE 15-Dec-2020 13:34:05 %LINK-I-Up: gi14 15-Dec-2020 13:34:05 %LINK-I-Up: gi15 15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpSingleNeighbour: Single LLDP neighbour on port gi15 - EEE operational state can be TRUE 15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpMultiNeighbours: Multiple LLDP neighbours on port gi13 - EEE operational state is FALSE 15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpMultiNeighbours: Multiple LLDP neighbours on port gi14 - EEE operational state is FALSE 15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpMultiNeighbours: Multiple LLDP neighbours on port gi15 - EEE operational state is FALSE 15-Dec-2020 13:34:05 %NT_GREEN-W-EeeLldpMultiNeighbours: Multiple LLDP neighbours on port gi16 - EEE operational state is FALSE 15-Dec-2020 13:34:10 %TRUNK-I-PORTADDED: Port gi13 added to Po2 15-Dec-2020 13:34:10 %LINK-I-Up: Po2 15-Dec-2020 13:34:10 %STP-W-PORTSTATUS: Po2: STP status Forwarding 15-Dec-2020 13:34:11 %STP-I-EDGEPORT: Attention: port Po2 from which the bpdu was received is configured as Fast Port 15-Dec-2020 13:34:11 %STP-W-PORTSTATUS: Po2: STP status Blocking 15-Dec-2020 13:34:11 %STP-W-LOOPBACKDET: Po2: STP Loopback Detection.
i tried disable and enable spanning-tree portfast on that port with no luck.
i think i miss something here, can someone help?
Thank you.
12-15-2020 08:37 AM
- Try to add this to the port-members : no macro auto smartport
M.
12-15-2020 08:57 AM
no macro auto smartport already in every port member. Is there anything sir?
12-15-2020 09:33 AM
- What NAS model and type is this ?
M.
12-15-2020 09:49 AM
It's qnap tds-16489u running qts, i forgot which version it is.
12-16-2020 01:37 AM
- Verify the LACP setup on the QNAS with :
M.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide