show int status | options

[paulkilcoyne]

Hi guys,

is there a way to filter out interfaces that are in vlan 4 and are in a connected state usinf the pipe optio or is there another way?

switch01#show interfaces status

Port      Name               Status       Vlan       Duplex  Speed Type

Fa1/0/1                      notconnect   3            auto   auto 10/100BaseTX

Fa1/0/2                      notconnect   4            auto   auto 10/100BaseTX

Fa1/0/3                      notconnect   3            auto   auto 10/100BaseTX

Fa1/0/4                      notconnect   4            auto   auto 10/100BaseTX

Fa1/0/5                      notconnect   3            auto   auto 10/100BaseTX

Fa1/0/6                      notconnect   4            auto   auto 10/100BaseTX

Fa1/0/7                      notconnect   3            auto   auto 10/100BaseTX

Fa1/0/8                      notconnect   4            auto   auto 10/100BaseTX

Fa1/0/9                      notconnect   3            auto   auto 10/100BaseTX

Fa1/0/10                     connected    4          a-full  a-100 10/100BaseTX

Fa1/0/11                     connected    3          a-full  a-100 10/100BaseTX

Fa1/0/12                     notconnect   4            auto   auto 10/100BaseTX

Fa1/0/13                     connected    3          a-full  a-100 10/100BaseTX

Fa1/0/14                     connected    4          a-full  a-100 10/100BaseTX

Fa1/0/15                     notconnect   3            auto   auto 10/100BaseTX

Fa1/0/16                      notconnect   3            auto   auto 10/100BaseTX

Fa1/0/17                     connected    3          a-full  a-100 10/100BaseTX

Fa1/0/18                     notconnect   4            auto   auto 10/100BaseTX

Fa1/0/19                     connected    3          a-full  a-100 10/100BaseTX

Fa1/0/20                     notconnect   4            auto   auto 10/100BaseTX

Fa1/0/21                     notconnect   3            auto   auto 10/100BaseTX

Fa1/0/22                     notconnect   4            auto   auto 10/100BaseTX

Fa1/0/23                     notconnect   3            auto   auto 10/100BaseTX

Fa1/0/24                     connected    4          a-full  a-100 10/100BaseTX

Fa1/0/25                     notconnect   3            auto   auto 10/100BaseTX

Fa1/0/26                     connected    4          a-full  a-100 10/100BaseTX

Fa1/0/27                     notconnect   7            auto   auto 10/100BaseTX

Fa1/0/28                     connected    4          a-full  a-100 10/100BaseTX

Fa1/0/29                     connected    3          a-full  a-100 10/100BaseTX

Fa1/0/30                     connected    4          a-full  a-100 10/100BaseTX

Fa1/0/31                     notconnect   3            auto   auto 10/100BaseTX

Fa1/0/32                     connected    4          a-full  a-100 10/100BaseTX

Fa1/0/33                     notconnect   3            auto   auto 10/100BaseTX

Fa1/0/34                     notconnect   4            auto   auto 10/100BaseTX

Fa1/0/35                     connected    3          a-full  a-100 10/100BaseTX

Fa1/0/36                     notconnect   4            auto   auto 10/100BaseTX

........................................................................................................

The stack goes on quite a bit further.

Thanks,

Paul

[danielmcollins]

Paul,

Do "sh int status | i connected 4"

When you do, copy n paste the "connected 4" part from current show int status output. You have to be sure it's looking for the correct amount of tabs or spaces.

Also, as an alternate, try "sh int status | conn.*4 "

Hth,

Dan

Sent from Cisco Technical Support iPhone App