Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...
Forum Posts
I have a lab that has 1 c2960cx switch, 1 WLC and 1 AP. I want the WLC to have 2 SSIDS(Wlans) on 1 AP, one for Internal users and 1 wlan for Guests. Can i somehow make it that theres 2 dhcp pools with 2 different subnets, one assigned for internal, ...
Testing with GNS.Switch SLA status is Timeout.Router is normal.What is the problem?? -SW-interface GigabitEthernet0/0 switchport access vlan 100 switchport mode accessinterface Vlan100 ip address 10.21.2.10 255.255.255.0 secondary ip address 172.29....
High level, I have a catalyst 3560G in my homelab. There are some ESXi hosts and physical 2012 server.I'm struggling to get my homelab to uplink to the home network. I am referencing the following Cisco Docs to setup. 1) Workstation 1 is on native ...
Resolved! How to stop a telnet session in IOS?
When I try to telnet but get no reply, if I want to stop the session, is there any way for that? Ctrl+c is not working. Ctrl+shift 6 neither.Thanks
Resolved! OSPF LSA Type 1 - Stub Network
Hi,I can't seem to find meaningful information regarding the Stub Network state in a Type 1 LSA.E.g Link connected to: another Router (point-to-point) (Link ID) Neighboring Router ID: 1.1.1.1 (Link Data) Router Interface address: 10.45.13.2...
and also this error : The system is unable to boot automatically. The BOOTenvironment variable needs to be set to a bootableimage.Switching, Catalyst 2000, LAN Switching
Hello all, I have installed a Cisco 9500 switch and a Firepower 2100 running ASA 9.8The issue I am facing its the I am trying to connect the switch and firewall via L2 sub interfacesare not coming up on ay port that I have configured sub interfaces ...
Resolved! Packet Capture is empty on Cat9300
I am trying to get a packet capture on a physical port (or VLAN interface) on a Cat 9300 running version 16.6.6But it does not capture any traffic.I think I have the capture set up correctly.If I set it to use a different interface, it works.I can se...
By looking at WS-C2960X-48FPD-L datasheet it does not specify support for IEEE 802.3i. Is this true?
Hi,I Have installed HWIC-2T card in my cisco 1921 router but it is not able to detected in router. please find the ver of routerCisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)Technical Support:...
Hola buenos dias.Esperando que se encuentren bien ..Tengo el detalle con un switch 3560 operando en capa 3, con 5 VLAN, con DHCP habilitado, el problema esta en las PC que se conectan a ese switch aparece con dos puertas de enlace predeterminadas, qu...
I have a lab with 2 interconnected switches and 2 vlan: vlan 10 and vlan 14. I would like to manage both vlan from a single PC connected to a free port of one of the switches. How can I configure the switch and the PC? Attached image...
Hi!I have to stack 8 switches (C2960X-48TD-L). There is a cable being shipped with each of them. But these cables are only 0.5 meters long. Which length is enough, reasoning from the minimal bending radius of the cable.I need to order the proper one....
Resolved! WS-C3650-48PD location in stack?
Hi, hopefully a quick question. We have a stack with WS-C3650-48PD's top and bottom (that carry the fibre uploads) and we wish to add two WS-C3650-48PS's to the bottom of the stack. Does it matter if we leave the PD switch where it is or would it be ...
Hi all, Could anyone can tell me why the output showed "0" packets but the "bytes output" is increasing?Is that the queuing value so it shows "0" ? Class-map: voice-traffic (match-any)0 packetsMatch: cos 60 packets, 0 bytes5 minute rate 0 bpsQueueing...
