cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
781
Views
0
Helpful
4
Replies

show port channel on cat 95k

nflnetwork
Level 1
Level 1

hi there i have configured a port channel with 4 total ports. 

 

is there a command i can run that will show the aggregate bandwidth?

 

ie. 4 x 10 GB ports - 40 GB total throughput ?

 

 

how can i see this ?

 

thanks,

1 Accepted Solution

Accepted Solutions

Reza Sharifi
Hall of Fame
Hall of Fame

Try,

sh int poxx

You should see something like this

MTU 1500 bytes, BW 40000000 Kbit/sec, DLY 10 usec

 

HTH

View solution in original post

4 Replies 4

Hello


@nflnetwork wrote:

hi there i have configured a port channel with 4 total ports. 

 

is there a command i can run that will show the aggregate bandwidth?

 

ie. 4 x 10 GB ports - 40 GB total throughput ?

 

 

how can i see this ?

 

thanks,


show port-channel summary

 


Please rate and mark as an accepted solution if you have found any of the information provided useful.
This then could assist others on these forums to find a valuable answer and broadens the community’s global network.

Kind Regards
Paul

this command does nto exist

9500-A#sh port ?
address Show secure address
interface Show secure interface
| Output modifiers
<cr> <cr>

9500-A#sh port

Reza Sharifi
Hall of Fame
Hall of Fame

Try,

sh int poxx

You should see something like this

MTU 1500 bytes, BW 40000000 Kbit/sec, DLY 10 usec

 

HTH

this works

Port-channel5 is up, line protocol is up (connected)
Hardware is EtherChannel, address is 9077.ee5b.aa0e (bia 9077.ee5b.aa0e)
Description: Port-Channel to Cisco-9200 Access
MTU 9216 bytes, BW 40000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 10Gb/s, link type is auto, media type is N/A
input flow-control is on, output flow-control is unsupported
Members in this channel: Twe1/0/46 Twe1/0/47 Twe2/0/46 Twe2/0/47
ARP type: ARPA, ARP Timeout 04:00:00
Last input 14:56:57, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 2836000 bits/sec, 678 packets/sec
5 minute output rate 2972000 bits/sec, 553 packets/sec
4447747 packets input, 1818085731 bytes, 0 no buffer
Received 113067 broadcasts (68275 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 68275 multicast, 0 pause input
0 input packets with dribble condition detected
6131958 packets output, 4513507241 bytes, 0 underruns
Output 81275 broadcasts (0 multicasts)
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco