SHOW VER has a network config file load from tftp. Would like to load from Flash.

haydavis · ‎06-26-2017

Unable to remove the load network config file via tftp. I find this in the show version on a 3650. The switch is prepared for IOS upgrade but I found a tftp config file in the show ver. I dont want to reload the switch as I would rather load the switch from config file on flash.

Any idea how to remove this and load config from flash?

MODEL: WS-C3650-48PS IOS: 03.03.05SE

SHOW VER:

<snip>

Uptime for this control processor is 45 weeks, 6 days, 22 hours, 56 minutes
System returned to ROM by reload
System restarted at 20:20:32 UTC Mon Aug 8 2016
System image file is "flash:packages.conf"
Network configuration file is "tftp://146.170.68.37/config.v833096.29469"
Last reload reason: reload

<snip>

Configuration register is 0x102

show boot:

---------------------------
Switch 1
---------------------------
Current Boot Variables:
BOOT variable = flash:cat3k_caa-universalk9.SPA.03.06.04.E.152-2.E4.bin;

Boot Variables on next reload:
BOOT variable = flash:cat3k_caa-universalk9.SPA.03.06.04.E.152-2.E4.bin;
Allow Dev Key = yes
Manual Boot = no
Enable Break = no

Desire to use the flash card nvram_config on boot.

diageoca-amhswi02-1609919#sh flash
-#- --length-- ---------date/time--------- path
2   79122052 May 12 2015 21:47:25.0000000000 +00:00 cat3k_caa-base.SPA.03.03.05SE.pkg
3    6521532 May 12 2015 21:47:25.0000000000 +00:00 cat3k_caa-drivers.SPA.03.03.05SE.pkg
4   34530288 May 12 2015 21:47:25.0000000000 +00:00 cat3k_caa-infra.SPA.03.03.05SE.pkg
5   34846028 May 12 2015 21:47:25.0000000000 +00:00 cat3k_caa-iosd-universalk9.SPA.150-1.EZ5.pkg
6   25170832 May 12 2015 21:47:25.0000000000 +00:00 cat3k_caa-platform.SPA.03.03.05SE.pkg
7   77456192 May 12 2015 21:47:25.0000000000 +00:00 cat3k_caa-wcm.SPA.10.1.150.0.pkg
8       1247 May 12 2015 21:47:37.0000000000 +00:00 packages.conf
9    2097152 Jun 26 2017 16:57:59.0000000000 +00:00 nvram_config
10      58869 Jun 16 2017 17:04:28.0000000000 +00:00 running-config
11       1216 Aug 08 2016 19:33:31.0000000000 +00:00 vlan.dat
12      58457 Feb 10 2017 16:13:33.0000000000 +00:00 backup-before-CHG0073022
13 302988468 Jun 26 2017 15:05:23.0000000000 +00:00 cat3k_caa-universalk9.SPA.03.06.04.E.152-2.E4.bin
917319680 bytes available (565817344 bytes used)

Mark Malone · ‎06-26-2017

Hi

Check the show run there must be a boot statement somewhere in it telling it to pull from tftp , remove it and set boot system flash:........

haydavis · ‎06-26-2017

Here is the boot statement in the show run.

boot-start-marker
boot system switch all flash:cat3k_caa-universalk9.SPA.03.06.04.E.152-2.E4.bin
boot-end-marker

A show run | i tftp produces nothing.

Here are options in the boot config. I dont see anything for tftp.

<removed>(config)#boot ?
allow_dev_key Allow_dev_key boot
enable-break   Enable break
manual         Manual boot
system         System Image

<removed>(config)#boot system ?
flash-1:      System image file
flash:        System image file
switch        Set system image for switches in the stack
tftp:         System image file
usbflash0-1: System image file
usbflash0:    System image file

haydavis · ‎06-27-2017

Fixed for those interested.

The fix was reload the router and it went away.

Assumption is the config was loaded via tftp from rommon(?). Not verified. And the show version "Network configuration file is " is informational of where running config came from and not what is loaded on next reload.