SP: c6k_power assert failed

[Rosa Ladeira]

Does anybody have ever heard about :

switches.log.6.gz:Sep  3 14:57:10 singer-outside 83: 5w1d: SP: c6k_power assert failed: '(power_status == POWER_ON || power_status == POWER_FAULTY)' at ../const/native-sp/c6k_power_port_mgmt.c:c6k_pwr_set_ilpower_from_cdp 2655

switches.log.6.gz:Sep  3 14:57:10 singer-outside 84: 5w1d: SP: -Traceback= 40BE78E8 40BF48C8 4125C2D4 413AE694 413AE9A0 409D3BA4 409D3B90

cat6509-wc1#sh version               

Cisco IOS Software, s3223_rp Software (s3223_rp-IPBASEK9-M), Version 12.2(33)SXI5, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Compiled Fri 22-Oct-10 14:31 by prod_rel_team

ROM: System Bootstrap, Version 12.2(17r)SX3, RELEASE SOFTWARE (fc1)

cat6509-wc1 uptime is 18 weeks, 1 day, 10 hours, 34 minutes

System returned to ROM by power on (SP by power on)

System restarted at 05:36:18 BRST Mon May 6 2013

System image file is "sup-bootdisk:s3223-ipbasek9-mz.122-33.SXI5.bin"

Last reload reason: Reload Command

cisco WS-C6509-E (R7000) processor (revision 1.4) with 458752K/65536K bytes of memory.

Processor board ID SMG1206N40E

R7000 CPU at 300Mhz, Implementation 0x27, Rev 3.3, 256KB L2, 1024KB L3 Cache

Last reset from power-on

3 Virtual Ethernet interfaces

337 Gigabit Ethernet interfaces

2 Ten Gigabit Ethernet interfaces

1915K bytes of non-volatile configuration memory.

65536K bytes of Flash internal SIMM (Sector size 512K).

Configuration register is 0x10

cat6509-wc1#sh power status all

                        Power-Capacity PS-Fan Output Oper

PS   Type               Watts   A @42V Status Status State

---- ------------------ ------- ------ ------ ------ -----

1    WS-CAC-6000W       2671.20 63.60  -      -      off

2    WS-CAC-6000W       2671.20 63.60  OK     OK     on

                        Pwr-Allocated  Oper

Fan  Type               Watts   A @42V State

---- ------------------ ------- ------ -----

1    WS-C6509-E-FAN      150.36  3.58  OK

                        Pwr-Requested  Pwr-Allocated  Admin Oper

Slot Card-Type          Watts   A @42V Watts   A @42V State State

---- ------------------ ------- ------ ------- ------ ----- -----

1    WS-X6148A-GE-45AF   112.56  2.68   112.56  2.68  on    on

2    WS-X6148A-GE-45AF   112.56  2.68   112.56  2.68  on    on

3    WS-X6148-GE-TX      103.74  2.47   103.74  2.47  on    on

4    WS-X6148A-GE-45AF   112.56  2.68   112.56  2.68  on    on

5    WS-SUP32-10GE-3B    175.98  4.19   175.98  4.19  on    on

6    (Redundant Sup)       -     -      175.98  4.19  -     -

7    WS-X6148A-GE-45AF   112.56  2.68   112.56  2.68  on    on

8    WS-X6148A-GE-45AF   112.56  2.68   112.56  2.68  on    on

9    WS-X6548-GE-TX      125.16  2.98   125.16  2.98  on    on

cat6509-wc1#

[Furose M]

looks like a power supply issue.. the power supply is currently in OFF state.

could you check if the power cable is working fine? if possible replace the power cable.

is there any other impact due to this error message?(like all the other moduels adn the PoE devices are working fine?)

[Rosa Ladeira]

I have already:

1.turn off/on;

2. fisically detach power suply;

3.change cable.

There are no other impacts.

Thanks

Rosa

[InayathUlla Sharieff]

Rosa,

Kindly run the following command:

Switch#show environment st

power-supply 1:

  power-supply 1 power-output-fail: failed  >>Please check if you are seeing this error?if yes then replace the PSU.

Switch#sh environment alarm

environmental alarms:

system minor alarm on power-supply 1 power-output-fail (raised 2w0d ago) >>check this msg as well.

Regards

Inayath

[Rosa Ladeira]

cat6509-wc2#show environment st

backplane:

  operating clock count: 2

  operating VTT count: 3

fan-tray 1:

  fan-tray 1 type: WS-C6K-9SLOT-FAN2

  fan-tray 1 version: 2

  fan-tray 1 fan-fail: OK

VTT 1:

  VTT 1 OK: OK

  VTT 1 outlet temperature: 27C

VTT 2:

  VTT 2 OK: OK

  VTT 2 outlet temperature: 31C

VTT 3:

  VTT 3 OK: OK

  VTT 3 outlet temperature: 27C

clock 1:

  clock 1 OK: OK, clock 1 clock-inuse: in-use

clock 2:

  clock 2 OK: OK, clock 2 clock-inuse: not-in-use

power-supply 1:

  power-supply 1 fan-fail: OK

  power-supply 1 power-input: AC low

  power-supply 1 power-output-mode: low

  power-supply 1 power-output-fail: OK

power-supply 2:

  power-supply 2 fan-fail: OK

  power-supply 2 power-input: AC low

  power-supply 2 power-output-mode: low

  power-supply 2 power-output-fail: OK

module 2:

  module 2 power-output-fail: OK

  module 2 outlet temperature: 28C

  module 2 inlet temperature: 27C

  module 2 VDB outlet temperature: 28C

  module 2 VDB inlet temperature: 26C

  module 2 VDB device-1 temperature: 27C

module 4:

  module 4 power-output-fail: OK

  module 4 outlet temperature: 27C

  module 4 inlet temperature: 26C

  module 4 device-1 temperature: 24C

  module 4 device-2 temperature: 26C

module 5:

  module 5 power-output-fail: OK

  module 5 outlet temperature: 34C

  module 5 inlet temperature: 27C

  module 5 device-1 temperature: 35C

  module 5 device-2 temperature: 36C

  module 5 asic-1 temperature: 25C

  module 5 RP outlet temperature: 33C

  module 5 RP inlet temperature: 33C

  module 5 EARL outlet temperature: 35C

  module 5 EARL inlet temperature: 24C

module 6:

  module 6 power-output-fail: OK

  module 6 outlet temperature: 30C

  module 6 inlet temperature: 26C

  module 6 device-1 temperature: 27C

  module 6 device-2 temperature: 30C

module 7:

  module 7 power-output-fail: OK

  module 7 outlet temperature: 30C

  module 7 inlet temperature: 26C

  module 7 device-1 temperature: 27C

  module 7 device-2 temperature: 30C

module 9:

  module 9 power-output-fail: OK

  module 9 outlet temperature: 29C

  module 9 inlet temperature: 32C

  module 9 device-1 temperature: 26C

  module 9 device-2 temperature: 28C

cat6509-wc2#sh environment alarm

environmental alarms:

  no alarms

cat6509-wc2#