Supervisor Engine 2T in VSS - Supported Modules

[michaelgitonga]

Hi,

I have a WS-C6509-E switch with the Supervisor Engine VS-S2T-10G-XL: Cat 6500 Sup 2T with 2x10GbE and 3 x 1GbE with MSFC5 PFC4XL.

Are the following modules supported with this SUP 2T in VSS setup:

• WS-X6704-10GE: Cat6500 4-port 10 Gigabit Ethernet Module (req. XENPAKs) WITH:
  
  • MEM-XCEF720-256M: Catalyst 6500 256MB DDR xCEF720 (67xx interface DFC3A)
    
  • WS-F6K-XENBLNKCVR: Catalyst 6500 Xenpak Blank Covers for WS-X6704-10GE
    
  • WS-F6700-CFC: Catalyst 6500 Central Fwd Card for WS-X67xx modules
    

• WS-X6748-GE-TX: Cat6500 48-port 10/100/1000 GE Mod: fabric enabled RJ-45 WITH:

  
  

  • MEM-XCEF720-256M: Catalyst 6500 256MB DDR xCEF720 (67xx interface DFC3A)

    
    

  • WS-F6700-CFC: Catalyst 6500 Central Fwd Card for WS-X67xx modules

    
    
• WS-X6148-GE-TX: Cisco Catalyst 6500 Series 48-Port 10/100/1000 RJ-45 Classic Interface Module
  

Thank you.

[Leo Laohoo]

I suspect you need to upgrade the PFC/DFC3 daughterboard with one that is PFC/DFC4.

[InayathUlla Sharieff]

Line-card compatibility

• WS-X6908-10G-2T, WS-X6908-10G-2TXL • WS-X6824-SFP-2T, WS-X6824-SFP-2TXL • WS-X6848-SFP-2T, WS-X6848-SFP-2TXL • WS-X6848-TX-2T, WS-X6848-TX-2TXL • WS-X6816-10T-2T, WS-X6816-10T-2TXL • WS-X6816-10G-2T, WS-X6816-10G-2TXL • WS-X6904-40G-2T, WS-X6904-40G-2TXL • WS-X6704-10GE with CFC • WS-X6724-SFP with CFC • WS-X6748-SFP with CFC • WS-X6748-GE-TX with CFC • WS-X6148A-RJ-45, WS-X6148A-45AF, WS-X6148-FE-SFP, WS-X6148A-GE-TX, WS-X6148A-GE-45AF, WS-X6148E-GE-45AT With a DFC4 or DFC4XL upgrade (WS-F6k-DFC4-A, WS-F6k-DFC4-AXL) • WS-X6704-10GE • WS-X6724-SFP • WS-X6748-SFP • WS-X6748-GE-TX With a DFC4 or DFC4XL upgrade (WS-F6k-DFC4-E, WS-F6k-DFC4-EXL) • WS-X6716-10G-3C, WS-X6716-10G-3CXL • WS-X6716-10T-3C, WS-X6716-10T-3CXL

REf:http://www.cisco.com/en/US/prod/collateral/modules/ps2797/ps11878/data_sheet_c78-648214_ps708_Products_Data_Sheet.html

HTH

Regards

Inayath