Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Resolved! backup ospf path
Could somebody tell me how to check whether other path available if OSPF route in the routing table fail?
Resolved! PBR missing command
I have a c3560e-universalk9-mz.122-55.SE5.I have 3 distinctive Vlan's:Vlan 100: 10.8.33.0/24Vlan 200: 10.8.133.0/24Vlan 300: 10.8.233.0/24Inter vlan routing is working.My default gateway is 10.8.33.254.I need to send some traffic in vlan 100 the rest...
Hi,I have a 6500 with 2 SUP7203B in Hot-Standby and when i reload slot 5 it goes in rommon (slot 6 is still up and takes over fine).When it is in rommon and I simply type boot, it loads the image fine.Why it doesnt boot by itself directly??I use SXI3...
Hello all.I am facing one issue with my CISCO 3560 Switch and need your help urgently.I have a Sever, Switch 3560 and a Router. Where Router is conncted with Internet.The Link connection is like:PC --- (Access Vlan 10) ---> CISCO ---(Access Vlan 10) ...
I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths. Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how...
Hello, I have a 2960 switch connected to another. The I need to verify that vlan0010 on one switch is forwarding tagged traffic between the other switch it is hooked up to through the Gi0/1 port. How do I verify this? I have a server that's multihome...
Resolved! Access switches choice
Hi AllFor a remote site we plan to purchase two POE access switches 48 ports 10/100/1000 with stacking options. I am not confused on selecting between 2960S and 3750 ; any suggestion based on experiencethanksVishal
Resolved! 3750X Stack high CPU
Seeing very high CPU on one of our 3750X stacks. Usally its around 30% but recently its 70, 80, 90 or maxed at 100% during the main day.IOS version c3750e-universalk9-mz.122-55.SE1.bin.Has a ten gig uplink connected to a nexus 7k and another ten gig...
Resolved! Wireless and Wireless Guest
Hello, I am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). Th...
Hey Folks,Was just wondering: Is SPAN a topic that is being discussed in the CCNP2 book? Because i just went over it, and i cant find it?! Neither does the lab manual mention anything about SPAN? I just had an exam (school) and there i was confronted...
So here is the deal, I have a server on switch A where port 3 is monitoring traffic for most of the ports on switch A. However I have other users on switch B that needs to have port 3 on switch A monitor as well. Is this possible? I have been reading...
Im having some major issues with my new setup. I have a Cisco Router (1921ISR) that is connected to the internet through a t1. In addition to that is another cable modem. Each of these are connected to my firebox through an external interface.My r...
Working with HP C7000 blade enclosure that has (2) Cisco CS3020 switches in it, connected to each other for redundancy.Each switch has an etherchannel uplink to a SINGLE HP Switch for storage traffic, which then carries storage traffic to a NAS ...
HiHow to enable port-channel load balance algorithm per channel not globally , coz i have multiple requirement for port-channel like dest-ip and dest-macthanksibrahim
What I’m looking to do is setup a net-flow monitor for traffic going across a PIX firewall. I know unfortunately I can’t do this directly from the PIX because it does not support net-flow.I do have a 2921 router on the same network that I have net-fl...
