Hi everyone
What‘s wrong with this alarm form the device of cisco 6509 & the users can not surfacing on the internet.
when I checked the device found that the 6509 looked be rebooted
below is the logging ：
*Dec 22 01:39:15.175: %ECC-SW1-3-SBE_HARD: Single bit *HARD* error detected at 0x00000000:0C0FF1A8
*Dec 22 01:39:22.199: %SYS-SW1-5-CONFIG_I: Configured from memory by console
*Dec 22 01:39:28.211: %OIR-SW1-6-INSPS: Power supply inserted in slot 1
*Dec 22 01:39:28.227: %C6KPWR-SW1-4-PSOK: power supply 1 turned on.
*Dec 22 01:39:28.239: %OIR-SW1-6-INSPS: Power supply inserted in slot 2
*Dec 22 01:39:28.243: %C6KPWR-SW1-4-PSOK: power supply 2 turned on.
*Dec 22 01:39:29.335: %SYS-SW1-5-RESTART: System restarted --
Cisco IOS Software, s2t54 Software (s2t54-IPSERVICESK9-M), Version 15.1(2)SY, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 04-Sep-13 12:37 by prod_rel_team
*Dec 22 01:39:31.051: %C6KENV-SW1-4-FANHPMODE: Switch 1 Fan-tray 1 is operating in high power mode
*Dec 22 01:39:31.167: %PFREDUN-SW1-6-ACTIVE: In-chassis standby initializing for SSO mode
*Dec 22 01:39:34.655: %FABRIC-SW1-5-FABRIC_MODULE_ACTIVE: The Switch Fabric Module in slot 5 became active.
*Dec 22 01:39:40.067: %DIAG-SW1-6-RUN_MINIMUM: Switch 1 Module 5: Running Minimal Diagnostics...
*Dec 22 01:39:40.155: %CONST_DIAG-SW1-6-DIAG_PORT_SKIPPED: Module 5 port 4 is skipped in TestLoopback due to: the port is used as a VSL link.
*Dec 22 01:39:40.891: %ECC-SW1-3-SBE_LIMIT: Single bit error detected and corrected at 0x00000000:7F4D0FF8
*Dec 22 01:39:40.979: %ECC-SW1-3-SYNDROME_SBE_LIMIT: 8-bit Syndrome for the detected Single-bit error: 0x42
*Dec 22 01:39:41.679: %OIR-SW1-6-INSREM: Switch 1 Physical Slot 7 - Module Type LINE_CARD inserted
*Dec 22 01:39:43.931: %OIR-SW1-6-INSREM: Switch 1 Physical Slot 9 - Module Type LINE_CARD inserted
*Dec 22 01:39:46.431: %CONST_DIAG-SW1-6-DIAG_PORT_SKIPPED: Module 5 port 4 is skipped in TestL2CTSLoopback due to: the port is used as a VSL link.
*Dec 22 01:39:52.007: %C6KPWR-SW1-4-UNSUPPORTED: unsupported module in slot 1, power not allowed: Unsupported module in Virtual Switch system.
*Dec 22 01:39:54.411: %OIR-SW1-6-INSREM: Switch 1 Physical Slot 1 - Module Type LINE_CARD inserted
*Dec 22 01:39:54.451: %OIR-SW1-6-INSREM: Switch 1 Physical Slot 3 - Module Type LINE_CARD inserted
...
*Dec 22 01:41:40.979: %ECC-SW1-3-SYNDROME_SBE_LIMIT: 8-bit Syndrome for the detected Single-bit error: 0x76
*Dec 22 01:41:45.523: %DIAG-SW1-6-DIAG_OK: Switch 1 Module 4: Passed Online Diagnostics
*Dec 22 01:41:46.599: %OIR-SW1-6-SP_INSCARD: Card inserted in Switch_number = 1, physical slot 4, interfaces are now online
*Dec 22 01:41:52.343: %DIAG-SW1-6-RUN_MINIMUM: Switch 1 Module 9: Running Minimal Diagnostics...
*Dec 22 01:42:10.891: %ECC-SW1-3-SBE_LIMIT: Single bit error detected and corrected at 0x00000000:05B61D20
*Dec 22 01:42:10.979: %ECC-SW1-3-SYNDROME_SBE_LIMIT: 8-bit Syndrome for the detected Single-bit error: 0x68
*Dec 22 01:42:12.111: %DIAG-SW1-6-DIAG_OK: Switch 1 Module 9: Passed Online Diagnostics
*Dec 22 01:42:14.923: %OIR-SW1-6-SP_INSCARD: Card inserted in Switch_number = 1, physical slot 9, interfaces are now online
*Dec 22 01:42:35.679: %DHCPD-SW1-4-PING_CONFLICT: DHCP address conflict: server pinged 192.168.2.1.
*Dec 22 01:42:36.679: %DHCPD-SW1-4-PING_CONFLICT: DHCP address conflict: server pinged 192.168.2.2.
*Dec 22 01:42:38.179: %DHCPD-SW1-4-PING_CONFLICT: DHCP address conflict: server pinged 192.168.2.3.
*Dec 22 01:42:40.891: %ECC-SW1-3-SBE_LIMIT: Single bit error detected and corrected at 0x00000000:06DD51C0
*Dec 22 01:42:40.979: %ECC-SW1-3-SYNDROME_SBE_LIMIT: 8-bit Syndrome for the detected Single-bit error: 0x60
*Dec 22 01:45:10.891: %ECC-SW1-3-SBE_LIMIT: Single bit error detected and corrected at 0x00000000:06DDB1A0
*Dec 22 01:45:10.979: %ECC-SW1-3-SYNDROME_SBE_LIMIT: 8-bit Syndrome for the detected Single-bit e!
*Dec 22 01:10:50.907: %ECC-SW1-3-SBE_LIMIT: Single bit error detected and corrected at 0x00000000:06DD5280
*Dec 22 01:10:51.003: %ECC-SW1-3-SYNDROME_SBE_LIMIT: 8-bit Syndrome for the detected Single-bit error: 0xB
*Dec 22 01:11:20.907: %ECC-SW1-3-SBE_LIMIT: Single bit error detected and corrected at 0x00000000:06DD9FC0
*Dec 22 01:11:21.003: %ECC-SW1-3-SYNDROME_SBE_LIMIT: 8-bit Syndrome for the detected Single-bit error: 0xB
*Dec 22 01:11:50.907: %ECC-SW1-3-SBE_LIMIT: Single bit error detected and corrected at 0x00000000:06DD9BE0
*Dec 22 01:11:51.003: %ECC-SW1-3-SYNDROME_SBE_LIMIT: 8-bit Syndrome for the detected Single-bit error: 0x93
*Dec 22 01:12:20.907: %ECC-SW1-3-SBE_LIMIT: Single bit error detected and corrected at 0x00000000:06DDAF60
*Dec 22 01:12:21.003: %ECC-SW1-3-SYNDROME_SBE_LIMIT: 8-bit Syndrome for the detected Single-bit error: 0x4F
*Dec 22 01:12:50.907: %ECC-SW1-3-SBE_LIMIT: Single bit error detected and corrected at 0x00000000:06DD9860
*Dec 22 01:12:51.003: %ECC-SW1-3-SYNDROME_SBE_LIMIT: 8-bit Syndrome for the detected Single-bit error: 0xDD
what's wrong with this problem？ what should I do ？ help me thanks!
from Jim
