04-12-2012 09:32 PM - edited 03-07-2019 06:06 AM
Hi there,
While I am an experienced systems guy, I am relatively new to network infrstructure. I have been assigned the task of trunking VLAN between a Nexus 3048 and a Force10 S4810. This would seem easy enough but I am really having a bear of a time getting it to work. Any help is greatly appreciated. I have devices configured on VLAN 602 on both sides but they just are not talking.
NX0S 3048
interface configuration
----------------------------------
interface Ethernet1/49
switchport mode trunk
---------------------------------
VLAN configuration
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Eth1/13, Eth1/14, Eth1/15
Eth1/16, Eth1/17, Eth1/18
Eth1/19, Eth1/20, Eth1/21
Eth1/22, Eth1/23, Eth1/24
Eth1/49, Eth1/50, Eth1/51
Eth1/52
600 OOB active Eth1/49, Eth1/50, Eth1/51
Eth1/52
602 Production active Eth1/25, Eth1/26, Eth1/27
Eth1/28, Eth1/29, Eth1/30
Eth1/31, Eth1/32, Eth1/33
Eth1/34, Eth1/35, Eth1/36
Eth1/37, Eth1/38, Eth1/39
Eth1/40, Eth1/41, Eth1/42
Eth1/43, Eth1/44, Eth1/45
Eth1/46, Eth1/47, Eth1/48
Eth1/49, Eth1/50, Eth1/51
Eth1/52
604 Storage active Eth1/49, Eth1/50, Eth1/51
Eth1/52
606 ClientVPN active Eth1/49, Eth1/50, Eth1/51
Eth1/52
608 Test active Eth1/49, Eth1/50, Eth1/51
Eth1/52
610 Backup active Eth1/49, Eth1/50, Eth1/51
Eth1/52
700 Headquarters act/lshut Eth1/11, Eth1/49, Eth1/50
Eth1/51, Eth1/52
800 HOUHQ-HOUDC active Eth1/12, Eth1/49, Eth1/50
Eth1/51, Eth1/52
1000 DMZ active Eth1/1, Eth1/2, Eth1/3, Eth1/4
Eth1/5, Eth1/6, Eth1/7, Eth1/8
Eth1/9, Eth1/10, Eth1/49
Eth1/50, Eth1/51, Eth1/52
Remote SPAN VLANs
-------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- --------------- -------------------------------------------
Force10 S4810
interface configuration
--------------------------------
interface TenGigabitEthernet 0/0
no ip address
switchport
no shutdown
VLAN configuration
Codes: * - Default VLAN, G - GVRP VLANs, R - Remote Port Mirroring VLANs, P - Primary, C - Community, I - Isolated
Q: U - Untagged, T - Tagged
x - Dot1x untagged, X - Dot1x tagged
G - GVRP tagged, M - Vlan-stack, H - VSN tagged
i - Internal untagged, I - Internal tagged, v - VLT untagged, V - VLT tagged
NUM Status Description Q Ports
* 1 Active U Te 0/1-2
600 Inactive T Te 0/0
602 Active T Te 0/0
U Te 0/12
604 Active T Te 0/0
U Te 0/36-47
606 Inactive T Te 0/0
608 Inactive T Te 0/0
610 Inactive T Te 0/0
700 Inactive T Te 0/0
800 Inactive T Te 0/0
1000 Inactive T Te 0/0
04-17-2012 03:43 PM
ok... turns out I had the cable plugged into the wrong port on the S4810. FYI... Cisco Nexus is numbered top to bottom. Force10 S4810 is numbered bottom to top.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide