I have an older 6509 with dual sup 2+
slot details:-
Slot 1: WS-X6K-SUP2-2GE
Slot 2: WS-X6K-SUP2-2GE
Slot 3:
Slot 4:
Slot 5:WS-C6500-SFM (Fabric module)
Slot 6:WS-SVC-FWM-1 (Firewall)
Slot 7:
Slot 8:
Slot 9:SW-SVC-IDSM2 (IDS)
I want to upgrade CatOS to native IOS.
your suggested IOS is 50MB size, & recomented Minimum Memory DRAM:256 MB Flash:64 MB
But this Switch Flash=32MB & memory=128MB. So I installed with another c6msfc2-boot-mz.121-20.E3.bin & c6msfc2-jsv-mz.121-20.E3.bin
(ie: I insert first sup-engine & installed IOS. then I remove converted supervisor from chassis and insert second sup-engine to first slot & installed )
After installation, I put both sup modules and switch on. Now first module is working (All LED is ON). but second slot is switched off & second sup LED not blinking.
could you please help me...
I removed second sup-engine and put Fabric module(slot 5), that time switch is overloading and rebooting.
display message: SP: oir_disable_notice: slot2: sec nmp failed to go online
then I removed fabric module & restarted switch,
& I checked dir bootflash: command. it displaying...
Router#dir bootflash:
Directory of bootflash:/
1 -rw- 1837920 May 22 2004 01:07:08 +00:00 c6msfc2-boot-mz.121-20.E3.bin
2 -rw- 14678592 May 22 2004 01:07:22 +00:00 c6msfc2-jsv-mz.121-20.E3.bin
3 -rw- 360965 May 30 2010 07:41:20 +00:00 crashinfo_20100530-074120
4 -rw- 361311 May 31 2010 04:10:26 +00:00 crashinfo_20100531-041026
After booting time informatins:-
00:00:34: RP: Currently running ROMMON from S (Gold) region
00:00:41: %SYS-5-CONFIG_I: Configured from memory by console
00:00:43: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) c6sup2_rp Software (c6sup2_rp-JS-M), Version 12.1(27b)E4, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by cisco Systems, Inc.
Compiled Fri 29-Feb-08 13:18 by hqluong
00:00:38: %C6K_PLATFORM-SP-5-MISMATCH: 'sup-bootflash' device programming algorithm mismatch detected on SP (module: 1), formatting is recommended.
00:00:38: SP: SP: Currently running ROMMON from S (Gold) region
00:00:40: %C6K_PLATFORM-SP-4-CONFREG_BREAK_ENABLED: The default factory setting for config register is 0x2102.It is advisable to retain 1 in 0x2102 as it prevents returning to ROMMON when break is issued.
00:00:43: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
00:00:43: %SYS-6-BOOTTIME: Time taken to reboot after reload = 704 seconds
00:00:43: %SYS-SP-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) c6sup2_sp Software (c6sup2_sp-SP-M), Version 12.1(27b)E4, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by cisco Systems, Inc.
Compiled Fri 29-Feb-08 13:22 by hqluong
00:00:44: %C6KENV-SP-4-FANVERCHK: Power-supply 1 inserted is only compatible with Version 1 fan-tray. Please make sure fan is low-output fan-tray
00:00:44: %OIR-SP-6-INSPS: Power supply inserted in slot 1
00:00:44: %C6KPWR-SP-4-PSOK: power supply 1 turned on.
00:00:45: %C6KENV-SP-4-FANVERCHK: Power-supply 2 inserted is only compatible with Version 1 fan-tray. Please make sure fan is low-output fan-tray
00:00:45: %OIR-SP-6-INSPS: Power supply inserted in slot 2
00:00:45: %C6KPWR-SP-4-PSOK: power supply 2 turned on.
00:00:45: %C6KPWR-SP-4-PSREDUNDANTBOTHSUPPLY: in power-redundancy mode, system is operating on both power supplies.
00:00:58: %DIAG-SP-6-RUN_MINIMUM: Module 1: Running Minimum Online Diagnostics...
00:01:05: %DIAG-SP-6-DIAG_OK: Module 1: Passed Online Diagnostics
00:01:05: %OIR-SP-6-INSCARD: Card inserted in slot 1, interfaces are now online
