10-13-2014 06:42 AM - edited 03-07-2019 09:05 PM
Hi Gurus,
Below are the three VLAN's I have created on my First Switch for the first time ion my lift after watching couple of videos.I am connected to the switch using a serial to usb cable via console.
sw1#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
101 lab1 active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/5
102 lab2 active Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10
103 lab3 active Fa0/11, Fa0/12, Fa0/13, Fa0/14
Fa0/15
1001 VLAN1001 active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
101 enet 100101 1500 - - - - - 0 0
102 enet 100102 1500 - - - - - 0 0
103 enet 100103 1500 - - - - - 0 0
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1001 enet 101001 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 tr 101003 1500 - - - - - 0 0
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trnet 101005 1500 - - - ibm - 0 0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
OS Version and type of Switch(L2)
sw1#show version
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA14, RELEASE SOFTWARE (fc1)
IP address assigned;;
interface Vlan1
no ip address
no ip route-cache
shutdown
!
interface Vlan101
ip address 10.0.1.1 255.255.255.0
no ip route-cache
!
interface Vlan102
ip address 11.0.10.10 255.255.255.0
no ip route-cache
shutdown
!
interface Vlan103
ip address 15.0.10.10 255.255.255.0
no ip route-cache
shutdown
IP address on my computer;
Wireless LAN adapter Wireless Network Connection:
Connection-specific DNS Suffix . : Home
Pv4 Address. . . . . . . . . . . : 192.168.0.12
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.0.1
Now I cannot ping any of the IP's assigned to the VLAN's. What to do with the VLAN's I've created [stupid and dumb question]. I want to play around the switch and connect it to a Cisco router(I have 5 routers and 5 switches, all different) and create my own lab.
please advise.
10-14-2014 04:02 AM
The most important part of this issue is that you are using a layer 2 switch and have created multiple vlans. To route between vlans you need a layer 3 device (could be a router or could be a layer 3 switch).
The other part of the issue is that you have created 3 vlans and associated addresses with them. Your PC is in a different subnet so logically it should be in a fourth vlan. And you need a layer 3 device to route between your PC and the switch subnets/vlans.
HTH
Rick
10-14-2014 05:35 PM
you are using L2 switch so the best way that you can ping between different vlans is "router on a stick".
you can change the ip address on your pc for example to 10.0.1.2 255.255.255.0 and 10.0.1.1 as default gateway to establish connectivity to vlan 101. It seems that you set ip address on your wireless card, you must set it on your ethernet card.
10-15-2014 05:09 AM
thanks everyone... I have the below sets of switches and routers at disposal...
2651XM; 2621XM; 2620XM; 2691; 1670; 2950-12/24/48
could you please advise of a lab for my CCNA
10-15-2014 12:03 PM
you can use below lab which is covering almost whole ccna exam concepts.
but establishing frame-relay in home lab requires more knowledge on networking, i recommend that you use GNS3-ER which now supports switch emulation too for frame-relay concepts.
However as far as i know, packet tracer is almost enough for ccna exam.
10-20-2014 11:39 PM
I do not know what GNS3-ER is. After google found some linki for GNS 3 and downloaded GNS3 0.8.7.
Explored it and could not find the lab you have mentioned. I m a novice in networking and know only few basic commands
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide