Solved: Re: VPC with HSRP and Intervlan Routing Design

Sajid Khan · ‎05-21-2023

We two nexus switch 9k and configured with VPC and HSRP, we have configured three vlan on that three switches. Vlan 2 for CCTV , vlan 3 for Monitering PC and vlan 1 for Dell Server that connected with two 9k switches by port channel. The two nexus switches is also connected two one distribution switch by port channel. when i do not know how , these two 9k switches are active / active in hsrp when i shutdown one uplink Eth1/2 of 9k1 which is active then traffic do not move on 9k2. let me correct if my design is okay.

9K1 Configuration ------------

config t
hostname 9K1-SW1
vlan 1
name DellRecordingServer
exit
vlan 2
name CCTV
exit
vlan 3
name MonitoringPC
exit
feature vpc
feature lacp
feature interface-vlan
int vlan 1
ip add 1.1.1.1 255.255.255.0
no shut
int vlan 2
ip add 192.168.2.1 255.255.255.0
no shut
int vlan 3
ip add 192.168.3.1 255.255.255.0
no shut
exit
vrf context VPC-KEEPALIVE
interface Ethernet 1/51
no shutdown
no switchport
vrf member VPC-KEEPALIVE
ip address 50.50.50.1 255.255.255.0
exit
interface Ethernet 1/49, Ethernet 1/50
no shut
switchport mode trunk
switchport trunk allowed vlan 1-3
description **VPC-PEERLINK**
channel-group 100 mode active
no shutdown
vpc domain 50
peer-gateway
role priority 20
peer-keepalive destination 50.50.50.2 source 50.50.50.1 vrf VPC-KEEPALIVE
exit
interface port-channel 100
description **VPC-PEERLINK**
no shutdown
switchport
switchport mode trunk
switchport trunk allowed vlan 1-3
spanning-tree port type network
vpc peer-link
exit
interface Ethernet 1/2
no shutdown
switchport mode trunk
switchport trunk allowed vlan 1-3
channel-group 2 mode on
interface port-channel 2
no shutdown
switchport mode trunk
switchport trunk allowed vlan 1-3
vpc 2
exit
interface eth 1/1
no shutdown
channel-group 1 mode on
interface port-channel 1
description *** Po1 to Server-1 ***
switchport
switchport mode access
switchport access vlan 1
vpc 1
exit

feature hsrp
interface Vlan 1
no shutdown
hsrp 1
ip 1.1.1.254
priority 200
preempt
exit
interface Vlan 2
no shutdown
hsrp 2
ip 192.168.2.254
priority 200
preempt
exit
interface Vlan 3
no shutdown
hsrp 3
ip 192.168.3.254
priority 200
preempt
exit

9K2 Configuration ------------

config t
hostname 9K2-SW2
vlan 1
name DellRecordingServer
exit
vlan 2
name CCTV
exit
vlan 3
name MonitoringPC
exit
feature vpc
feature lacp
feature interface-vlan
int vlan 1
ip add 1.1.1.2 255.255.255.0
no shut
int vlan 2
ip add 192.168.2.2 255.255.255.0
no shut
int vlan 3
ip add 192.168.3.2 255.255.255.0
no shut
exit
vrf context VPC-KEEPALIVE
interface Ethernet 1/51
no shutdown
no switchport
vrf member VPC-KEEPALIVE
ip address 50.50.50.2 255.255.255.0
exit
interface Ethernet 1/49, Ethernet 1/50
description **VPC-PEERLINK**
channel-group 100 mode active
no shutdown
vpc domain 50
peer-gateway
role priority 40
peer-keepalive destination 50.50.50.1 source 50.50.50.2 vrf VPC-KEEPALIVE
exit
interface port-channel 100
description **VPC-PEERLINK**
no shutdown
switchport
switchport mode trunk
switchport trunk allowed vlan 1-3
spanning-tree port type network
vpc peer-link
exit

interface Ethernet 1/2
no shutdown
switchport mode trunk
switchport trunk allowed vlan 1-3
channel-group 2 mode on
interface port-channel 2
no shutdown
switchport mode trunk
switchport trunk allowed vlan 1-3
vpc 2
exit
interface eth 1/1
no shutdown
channel-group 1 mode on
interface port-channel 1
description *** Po1 to Server-1 ***
switchport
switchport mode access
switchport access vlan 1
vpc 1
exit

feature hsrp
interface Vlan 1
no shutdown
hsrp 1
ip 1.1.1.254
priority 150
preempt
exit
interface Vlan 2
no shutdown
hsrp 2
ip 192.168.2.254
priority 150
preempt
exit
interface Vlan 3
no shutdown
hsrp 3
ip 192.168.3.254
priority 150
preempt
exit

Distribution switch configuration .....................

config t
hostname DistSW
vlan 1
name DellRecordingServer
exit
vlan 2
name CCTV
exit
vlan 3
name MonitoringPC
exit
interface range ethernet 0/0-1
no shutdown
switchport mode trunk
switchport trunk allowed vlan 1-3
channel-group 2 mode on
exit

Sajid Khan · ‎05-25-2023

No one can reply to me?

View solution in original post

MHM Cisco World · ‎05-29-2023

PING 2000,
the disruption in traffic when I shut one of port member, the only one loss when I no shut the port

View solution in original post

MHM Cisco World · ‎05-29-2023

this OK,
show port-channel in three SW (two NSK and one other SW) when link is UP and Down,

NOTE:- you use RSTP as MODE ? if Yes and it Lab change the config to be PVST

View solution in original post

MHM Cisco World · ‎05-21-2023

HSRP in vPC of NSK is active/active, this the goal of vPC NSK

Sajid Khan · ‎05-21-2023

Yes, i know that HSRP is active /active in VPC but if one link goes down then traffic should move to another switch and there should be no drop in traffic.

Sajid Khan · ‎05-21-2023

Kindly check my topology, this design is okay.

MHM Cisco World · ‎05-21-2023

I will check it

Sajid Khan · ‎05-21-2023

so you mean that for po1 and po2 the vpc number shoud be 50 for both. i think vpc number and vpc domain number are different things.

Sajid Khan · ‎05-21-2023

Can you correct my configuration file.

MHM Cisco World · ‎05-21-2023

I will check it

MHM Cisco World · ‎05-21-2023

can I see
show vpc brief <<-
show port-channel summary <<-

Sajid Khan · ‎05-22-2023

9K1-SW1# show vpc brief
Legend:
(*) - local vPC is down, forwarding via vPC peer-link

vPC domain id : 50
Peer status : peer adjacency formed ok
vPC keep-alive status : peer is alive
Configuration consistency status : success
Per-vlan consistency status : success
Type-2 consistency status : success
vPC role : primary
Number of vPCs configured : 2
Peer Gateway : Enabled
Dual-active excluded VLANs : -
Graceful Consistency Check : Enabled
Auto-recovery status : Disabled
Delay-restore status : Timer is off.(timeout = 30s)
Delay-restore SVI status : Timer is off.(timeout = 10s)
Operational Layer3 Peer-router : Disabled

vPC Peer-link status
---------------------------------------------------------------------
id Port Status Active vlans
-- ---- ------ -------------------------------------------------
1 Po100 up 1-3

vPC status
----------------------------------------------------------------------------
Id Port Status Consistency Reason Active vlans
-- ------------ ------ ----------- ------ ---------------
1 Po1 up success success 1

2 Po2 up success success 1-3

Please check "show vpc consistency-parameters vpc <vpc-num>" for the
consistency reason of down vpc and for type-2 consistency reasons for
any vpc.

9K1-SW1# show port-channel summary
Flags: D - Down P - Up in port-channel (members)
I - Individual H - Hot-standby (LACP only)
s - Suspended r - Module-removed
b - BFD Session Wait
S - Switched R - Routed
U - Up (port-channel)
p - Up in delay-lacp mode (member)
M - Not in use. Min-links not met
--------------------------------------------------------------------------------
Group Port- Type Protocol Member Ports
Channel
--------------------------------------------------------------------------------
1 Po1(SU) Eth NONE Eth1/1(P)
2 Po2(SU) Eth NONE Eth1/2(P)
100 Po100(SU) Eth LACP Eth1/49(P) Eth1/50(P)
9K1-SW1#

MHM Cisco World · ‎05-22-2023

every this is perfect the vPC keepalive alive and Peer link is UP and OK and all config check is success
vPC domain id : 50
Peer status : peer adjacency formed ok
vPC keep-alive status : peer is alive
Configuration consistency status : success
Per-vlan consistency status : success
Type-2 consistency status : success
vPC role : primary
Number of vPCs configured : 2
Peer Gateway : Enabled
Dual-active excluded VLANs : -
Graceful Consistency Check : Enabled
Auto-recovery status : Disabled
Delay-restore status : Timer is off.(timeout = 30s)
Delay-restore SVI status : Timer is off.(timeout = 10s)
Operational Layer3 Peer-router : Disabled

vPC Peer-link status
---------------------------------------------------------------------
id Port Status Active vlans
-- ---- ------ -------------------------------------------------
1 Po100 up 1-3

MHM Cisco World · ‎05-22-2023

1 Po1(SU) Eth NONE Eth1/1(P)
2 Po2(SU) Eth NONE Eth1/2(P)
100 Po100(SU) Eth LACP Eth1/49(P) Eth1/50(P) <<- this Peer-link

all PO is SU and port member is Pending, so all config is correct

Sajid Khan · ‎05-22-2023

Ok, configuration is correct but when i shut down Eth1/2 of NK1 on nexus switch then the traffic drop and it passing through Nk2.

In normal Hsrp when we shut down a link then traffic should move on another switch.

Sajid Khan · ‎05-22-2023

Ok, configuration is correct but when i shut down Eth1/2 of NK1 on nexus switch then the traffic drop and it should pass through Nk2, just like normal hsrp.

In normal Hsrp when we shut down a link then traffic should move on another switch.

MHM Cisco World · ‎05-23-2023

I think from Yesterday about this issue, are you sure you push HSRP VIP to host not IP of VLAN SVI of NSK1 via DHCP as GW?
can you check the GW in Host/server?