Im have the same issue on

Frank Lothar Weber · ‎05-25-2015

Hi, folks.

When upgrading a Cat3750X-48T-S to 15.2.2Ex or even 15.2.3Ex each reboot shows some error messages when checking

the boot via console:

cisco WS-C3750X-48 (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1438K0KF
Last reset from power-on
1 Virtual Ethernet interface
1 FastEthernet interface
52 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : 58:8Dxxxxxxxx
Motherboard assembly number     : 73-12552-04
Motherboard serial number       : xxxxxxxxxxxxxxxxxxx
Model revision number           : A0
Motherboard revision number     : A0
Model number                    : WS-C3750X-48T-S
Daughterboard assembly number   : xxxxxxxxxxxxxxxxxxxxx
Daughterboard serial number     : xxxxxxxxxxxx
System serial number            : xxxxxxxxxxx
Top Assembly Part Number        : 800-31326-01
Top Assembly Revision Number    : A0
Version ID                      : V01
CLEI Code Number                : COMJT00ARA
Hardware Board Revision Number : 0x02

Switch Ports Model                     SW Version            SW Image
------ ----- -----                     ----------            ----------
*    1 54    WS-C3750X-48              15.2(3)E1             C3750E-UNIVERSALK9-M

Command execution is locked, Please try later.
switchport mode access
^
% Invalid input detected at '^' marker.

switchport block unicast
^
% Invalid input detected at '^' marker.

switchport port-security maximum 3
^
% Invalid input detected at '^' marker.

switchport port-security maximum 2 vlan access
^
% Invalid input detected at '^' marker.

switchport port-security
^
% Invalid input detected at '^' marker.

switchport port-security aging time 2
switchport protected
^
% Invalid input detected at '^' marker.

^
% Invalid input detected at '^' marker.

switchport port-security violation restrict
^
% Invalid input detected at '^' marker.

switchport port-security aging type inactivity
^
% Invalid input detected at '^' marker.

load-interval 30
^
% Invalid input detected at '^' marker.

storm-control broadcast level pps 1k
^
% Invalid input detected at '^' marker.

storm-control multicast level pps 2k
^
% Invalid input detected at '^' marker.

storm-control action trap
^
% Invalid input detected at '^' marker.

spanning-tree portfast
^
% Invalid input detected at '^' marker.

spanning-tree bpduguard enable
^
% Invalid input detected at '^' marker.

ip dhcp snooping limit rate 15
^
% Invalid input detected at '^' marker.

srr-queue bandwidth share 1 30 35 5
^
% Invalid input detected at '^' marker.

priority-queue out
^
% Invalid input detected at '^' marker.

mls qos trust cos
^
% Invalid input detected at '^' marker.

service-policy input AUTOCONF-SRND4-CISCOPHONE-POLICY
^
% Invalid input detected at '^' marker.

Press RETURN to get started!

The config of the device is empty and this repeats every reboot ....

Anybody also seen this ??? Any clue what it might be ??

Rgs

Frank

Brian Shoemaker · ‎06-11-2015

New switch never plugged into any network or ever been configured, just updated IOS and I get same message.

Mine is on a WS-C3750X-24T-S running 15.2(3)E1 (C3750E-UNIVERSALK9-M) c3750e-universalk9-mz.152-3.E1.bin.

Brian

Adam Knutson · ‎08-25-2015

I get the exact same error output on initial boot after reload. It's obviously related to autoconf, the switch acts as if it is trying to apply the following configuration from an auto config template, even though we aren't using that feature.

Switch#show auto configuration template builtin
Template Name:   IP_PHONE_INTERFACE_TEMPLATE
Template Definition:switchport mode access
switchport block unicast
switchport port-security maximum 3
switchport port-security maximum 2 vlan access
switchport port-security
switchport port-security aging time 2
switchport port-security violation restrict
switchport port-security aging type inactivity
load-interval 30
storm-control broadcast level pps 1k
storm-control multicast level pps 2k
storm-control action trap
spanning-tree portfast
spanning-tree bpduguard enable
ip dhcp snooping limit rate 15
srr-queue bandwidth share 1 30 35 5
priority-queue out
mls qos trust cos
service-policy input AUTOCONF-SRND4-CISCOPHONE-POLICY
exit

d79dannyd · ‎11-09-2015

Im have the same issue on 3560 with 15.2. Have you found a workaround or fix for this?

Thanks

Danny

Adam Knutson · ‎11-10-2015

We opened a TAC case and they came back with this:

Hello Team,

I was able to replicate this problem, I enabled autoconfig and then disabled it, after the reload I received same errors. I found this is a defect on the software that affects only new IOS releases on train 15.2E. I successfully downgraded the software to a different train:15.0(2)SE6/ 15.0(2)SE8 and the errors disappeared.

https://software.cisco.com/download/release.html?mdfid=282979361&flowid=2627&softwareid=280805680&release=15.0.2-SE8&relind=AVAILABLE&rellifecycle=MD&reltype=latest

This appears to be only a cosmetic issue as the running config does not show any of those outputs.

However if you would like to remove this errors you would need to downgrade the software to a different train.

Let me know if you have any doubt. Thanks!

Veronica Flores

Cisco TAC

Phone: <removed>

Email: <removed>

To update your case (requires a support contract):

https://tools.cisco.com/ServiceRequestTool/scm/mgmt/case

Cisco Worldwide Contact:

http://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html

Direct Managers: Juanita Roda | Fabian Arce

Phone: <removed>

Email: <removed>

Team Lead: Jorge Jara

Phone: <removed>

Email:<removed>

Frank Lothar Weber · ‎11-13-2015

Yeah, right. Thank god there is TAC .... !!!

All this we knew already ....

Downgrading to 15.0(x)SE is not an option, because the reason we chose 15.2.xE is that it supports IBNS 2.0 !!! 15.0(x) doesn't !!!

Cosmetic or not, since IBNS 2.0 does not work correctly in the 15.2.x releases either (see https://supportforums.cisco.com/discussion/12597491/ibns-20-interface-template-does-not-work-expected-ios-152xe), this bug should be fixed in upcoming releases ....

Rgs

Frank

Jose Solano · ‎11-17-2015

Hi all,

There is an internal bug that was identify identified and will be fixed in 15.2(4)E1, which should be available by the end of the year, it is known that the version 15.2(2)E3 will present the errors on boot up but the lost config issue is not seen.

The errors should be just cosmetic.

Regards,

Jose

shawn.murphy1 · ‎01-11-2016

I may be nit picking semantics here, but the original copy of the post from the engineer found the commands not in running config.

What about derived config ? Or was that the meaning?

Thanks,

Shawn

Gorkagere · ‎05-15-2018

I have same problem but in my case prompt stops on "% Invalid input detected at '^' marker" and cannot access to the switch.

By the way, running IOS is 15.2(2.7)E

Regards,

Gorka.

Weird error when upgrading to 15.2E