Hi,
We are seeing this on a Cat4500 VSS switch
%C4K_SWITCHINGENGINEMAN-3-VFEFLTOOMANYPARITYERRORS: VFE FL module sees too many fwdMem1CorrectedEcc
According to this:
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/12-2/53SG/system/messages/sem_53sg/emsg.html
the SUP should get automatically rebooted. But that didn't happen. We are dropping pings when pinging the switch.
Since it is mostly a hardware related issue, I thought about reseating the SUP with the issue. But I can't tell exactly which one. I'm suspecting the standby SUP because I see this:
----------------- show diagnostic result module all detail ------------------
Current bootup diagnostic level: minimal
module 1: SerialNo : **********
Overall Diagnostic Result for module 1 : UNTESTED
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
___________________________________________________________________________
1) supervisor-bootup ---------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
Power-On-Self-Test Results for ACTIVE Supervisor
prod: WS-X45-SUP8-E part: 73-14915-06 serial: CAT1839L7KE
Power-on-self-test for Module 1: WS-X45-SUP8-E
CPU Subsystem Tests ...
seeprom: Pass
Traffic: L3 Loopback ...
Test Results: Pass
Traffic: L2 Loopback ...
Test Results: Pass
Module 1 Passed
___________________________________________________________________________
2) linecard-online-diag ------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
Slot Ports Card Type Diag Status Diag Details
---- ----- -------------------------------------- ---------------- ------------
1 8 Sup 8-E 10GE (SFP+), 1000BaseX (SFP) Passed None
Detailed Status
---------------
. = Pass U = Unknown
L = Loopback failure S = Stub failure
P = Port failure
E = SEEPROM failure G = GBIC integrity check failure
Ports 1 2 3 4 5 6 7 8
. . . . . . . .
___________________________________________________________________________
3) stub-rx-errors ------------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
4) supervisor-rx-errors ------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
Am I right in my assumption? Can we just re-seat the standby SUP or do we have to reload the whole standby switch?
