cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1152
Views
0
Helpful
3
Replies

WS-C4507R - IOS Upgrade

maxxam-can
Level 1
Level 1

Morning Guys,

First issue I'm having is finding the correct IOS image to upgrade my switch. I'm hoping by posting here someone will point me to the correctplace to get the file. I've spent a while on cisco site but unable to find what I'm hoping would be the correct image. Below are some information to help you guys.

--- Show version

Cisco Internetwork Operating System Software

IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12.1(19)EW1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Mon 28-Jul-03 16:10 by eaarmas

Image text-base: 0x00000000, data-base: 0x00F12E30

ROM: 12.1(20r)EW

Dagobah Revision 86, Swamp Revision 28

!

System image file is "bootflash:cat4000-i9s-mz.121-19.EW1.bin"

!

cisco WS-C4507R (XPC8245) processor (revision 7) with 524288K bytes of memory.

show module

Chassis Type : WS-C4507R

Power consumed by backplane : 40 Watts

Mod Ports Card Type                              Model              Serial No.

---+-----+--------------------------------------+------------------+-----------

1     2  1000BaseX (GBIC) Supervisor(active)    WS-X4515           JAE080200S5

2     2  1000BaseX (GBIC) Supervisor(standby)   WS-X4515           JAE0802028B

3    48  10/100BaseTX (RJ45)                    WS-X4148-RJ        JAE07510SEC

4    48  10/100BaseTX (RJ45)                    WS-X4148-RJ        JAE0751010W

5    48  10/100BaseTX (RJ45)                    WS-X4148-RJ        JAE0752019F

6    48  10/100BaseTX (RJ45)                    WS-X4148-RJ        JAE07510S4V

7    18  1000BaseX (GBIC)                       WS-X4418-GB        JAE0746099M

M MAC addresses                    Hw  Fw           Sw               Status

--+--------------------------------+---+------------+----------------+---------

1 000e.d798.1880 to 000e.d798.1881 3.1 12.1(20r)EW  12.1(19)EW1, EAR Ok

2 000e.d798.1882 to 000e.d798.1883 3.1 12.1(20r)EW  12.1(19)EW1,     Ok

3 000e.8359.95c0 to 000e.8359.95ef 3.1                               Ok

4 000e.8359.2a80 to 000e.8359.2aaf 3.1                               Ok

5 000e.8366.7360 to 000e.8366.738f 3.1                               Ok

6 000e.831d.1220 to 000e.831d.124f 3.1                               Ok

7 000d.bcf6.547e to 000d.bcf6.548f 1.4                               Ok

!

Hope this was enough.

Looking forward to any assistance.

3 Replies 3

mvsheik123
Level 7
Level 7

Hi,

WS-X4515 is Sup IV. Your current s/w is 'Basic L3'. If you just need basic L3 without any SSH or advance routing protocol support, you can go with 'ip base w/o crypto' (cat4500-ipbase-mz.122-54.SG1.bin).

DRAM & Flash may be sufficient in your case, but I suggest you to read the relase notes before planning on upgrade.

hth

MS

Hi Jason,

The IOS version you are using is cat4000-i9s-mz.121-19.EW1.bin which is a basic L3 IOS version  and supervisor Engine is IV.

The latest IOS release of EW train of Basic L3 version is cat4000-i9s-mz.122-20.EW4.bin

The link for downloading this image is given below.

- http://www.cisco.com/cisco/software/release.html?mdfid=277241602&flowid=3513&softwareid=280805680&

release=12.2.20-EW4&rellifecycle=ED&relind=AVAILABLE&reltype=latest

Also you can check the feature sets available in this IOS version by using Cisco Feature navigator.

Link for Cisco Feature Navigator is

-http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp

Search by image.

Hope this helps.

-Somu Jayaraman

Rate this answer if it is helpful.

Hi Somu,

Thanks for the correction. Thought existing IOS can be matched to 12.2 (54) ip base version.

Thanks

MS

Review Cisco Networking for a $25 gift card