03-24-2009 05:36 PM - edited 03-06-2019 04:47 AM
Hi,
When i boot up my WS-C6500-E only the supervisor module gets powered up. The other modules are completely dark. I think the supervisor has a problem in the module bringup process. Her is a print of the supervisor diagnostics:
Current bootup diagnostic level: minimal
Module 5 : 9-port 1000BaseX Supervisor, Serial No : SAL1021P5C0
Environmental Status (. = Pass, F = Fail, U = Unknown, N = Not Present)
PS1: F PS2: F PS1 Fan: F PS2 Fan: F
Chassis-Ser-EEPROM: F
Clock(A/B): A Clock A: . Clock B: .
VTT1: . VTT2: . VTT3: .
Network Management Processor (NMP) Status: (. = Pass, F = Fail, U = Untested)
ROM: . Flash-EEPROM: . Ser-EEPROM: . NVRAM: . EOBC Comm: F
Line Card Firmware Status for Module 5 : PASS
Line Card Diag Status for Module 5 (. = Pass, F = Fail, N = N/A, U = Untested)
Port Status :
Ports 1 2 3 4 5 6 7 8 9
--------------------------------
. . . . . . . . .
SFP Status :
Ports 1 2 3 4 5 6 7 8 9
--------------------------------
N N N N N N N N N
Module 5:
Overall Diagnostic Result for Module 5 : MAJOR ERROR
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
1 ) FirmwareDiagStatus --------------> .
2 ) TestLoopback:
Ports 1 2 3 4 5 6 7 8 9
--------------------------------
F F F F F F F F F
3 ) TestActiveToStandbyLoopback:
Ports 1 2 3 4 5 6 7 8 9
--------------------------------
U U U U U U U U U
4 ) TestTxPathMonitoring ------------> U
5 ) TestInlineRewrite:
Ports 1 2 3 4 5 6 7 8 9
--------------------------------
U U U U U U U U U
6 ) TestActiveToStandbyInlineRw:
Ports 1 2 3 4 5 6 7 8 9
--------------------------------
U U U U U U U U U
7 ) TestNewLearn --------------------> F
8 ) TestIndexLearn ------------------> F
9 ) TestDontLearn -------------------> U
10 ) TestDontForward -----------------> U
11 ) TestConditionalLearn ------------> F
12 ) TestBadBpdu ---------------------> U
13 ) TestTrap ------------------------> U
14 ) TestMatch -----------------------> U
15 ) TestSpan ------------------------> U
16 ) TestCapture ---------------------> U
17 ) TestProtocolMatch ---------------> U
18 ) TestChannel ---------------------> U
19 ) TestL3Span ----------------------> F
20 ) TestFibDevices ------------------> F
21 ) TestIPv4FibShortcut -------------> F
22 ) TestL3Capture2 ------------------> F
23 ) TestL3VlanMet -------------------> F
24 ) TestAclPermit -------------------> F
25 ) TestAclDeny ---------------------> F
26 ) TestQoSTcamTest -----------------> F
27 ) TestFibTcamSSRAM ----------------> U
03-24-2009 05:50 PM
I'm suspecting it's because of your power supply. What is your current power supply and what are your cards?
03-24-2009 09:54 PM
Im not sure exactly what model the powersupplies are but both the 'input ok' and 'fan ok' LEDs are green on both. I have tried moving the supervisor to different locations but always with the same result. I have 1 module with 48 ethernet ports and 4 modules with 24 MTRJ (fiber) ports each. I tried moving theese around but without results.
03-24-2009 05:52 PM
I would put in a TAC case on this. Something is not right with the supervisor showing a "MAJOR ERROR". It appears to be a hardware problem with the supervisor in slot five.
HTH,
Mark
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide