WS-X6708-10G-3CXL doesn't work on WS-C6506-E
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-28-2012 05:11 AM - edited 03-07-2019 09:43 AM
Hello,
we can't start WS-X6708-10G-3CXL on WS-C6506-E
here is more info:
SW0#sh ver
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SRA7, RELEASE SOFTWARE (fc2)
SW0#sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1206FBVM
2 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL0917A0MC
3 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1232ZH7F
4 8 FRU type (0x6003, 0x3F8(1016)) WS-X6708-10GE SAL1625EX75
6 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL092756DS
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 001e.f783.9bf4 to 001e.f783.9c0b 3.1 12.2(18r)S1 12.2(33)SRA7 Ok
2 0013.c424.34b8 to 0013.c424.34e7 10.1 7.2(1) 8.6(0.259)CA Ok
3 0022.55f4.04c0 to 0022.55f4.04d7 3.2 12.2(18r)S1 12.2(33)SRA7 Ok
4 442b.034f.6f98 to 442b.034f.6f9f 3.5 Unknown Unknown PwrDown
6 0012.dae4.7f10 to 0012.dae4.7f13 4.4 8.1(3) 12.2(33)SRA7 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Centralized Forwarding Card WS-F6700-CFC SAL1205F0ES 4.0 Ok
3 Centralized Forwarding Card WS-F6700-CFC SAL1226V4AS 4.1 Ok
4 Distributed Forwarding Card WS-F6700-DFC3CXL SAL1626FA3U 1.7 PwrDown
6 Policy Feature Card 3 WS-F6K-PFC3B SAL092753DG 2.1 Ok
6 MSFC3 Daughterboard WS-SUP720 SAL09253GB9 2.3 Ok
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
3 Pass
4 Not Applicable
6 Pass
we did try on conf t mode "power enable module 3" and it didn't work
Oct 28 15:01:06: %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 4, power not allowed: Unknown Card Type.
Oct 28 15:01:56: %SYS-5-CONFIG_I: Configured from console by bill3 on vty0 (89.223.47.133)
Oct 28 15:03:36: %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 4, power not allowed: Unknown Card Type.
--
SW0#sh power
system power redundancy mode = combined
system power total = 6325.20 Watts (150.60 Amps @ 42V)
system power used = 1038.66 Watts (24.73 Amps @ 42V)
system power available = 5286.54 Watts (125.87 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-4000W-INT 3795.12 90.36 OK OK on
2 WS-CAC-6000W 5771.64 137.42 OK OK on
Pwr-Allocated Oper
Fan Type Watts A @42V State
---- ------------------ ------- ------ -----
1 WS-C6506-E-FAN 98.70 2.35 OK
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
1 WS-X6724-SFP 125.16 2.98 125.16 2.98 on on
2 WS-X6548-GE-TX 125.16 2.98 125.16 2.98 on on
3 WS-X6724-SFP 125.16 2.98 125.16 2.98 on on
4 WS-X6708-10GE 473.76 11.28 - - on off (not supported)
5 (Redundant Sup) - - 282.24 6.72 - -
6 WS-SUP720-3B 282.24 6.72 282.24 6.72 on on
- Labels:
-
Other Switching
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-28-2012 08:39 AM
Hi,
Can you move the module to a different slot and try again?
Also, you are running a very old version of IOS. Try a later version of SXi or SXJ.
HTH
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-28-2012 09:05 AM