06-21-2018 04:10 PM - edited 03-01-2019 01:35 PM
Running UCS 3.2.2f with B480M5s with same firmware. I have a Power Control policy to impose "No-Cap" Power Control. Each server where it is applied, i get the F0637 fault. If I remove the policy, the fault clears. I had seen a bug in 3.1 but resolved in same. CSCvc02297. I had trying the work-around of power down via the OS and boot via UCSM. This did not clear the fault.
Anyone seen this elsewhere?
Thank you for any insight,
Dan Laden
06-21-2018 07:08 PM - edited 06-22-2018 03:19 AM
Greetings.
Trying pulling some power related settings from the cli:
#scope chassis x
#scope server y
#show power-budget expand detail
#scope chassis x
#show power-budget detail
exit out to top level of ucsm cli
#connect iom x (where x is chassis with blade in question)
#show platform software cmcctrl power config
#show platform software cmcctrl dmclient psreadings (if output is all zeros, then connect to other IOM in same chassis
You may want to try re-acking server if you haven't already...
Thanks,
Kirk...
06-22-2018 08:15 AM
ucs-A /chassis/server # show power-budget expand detail
Budget:
AdminCommitted (W): 0
ucs-A /chassis # show power-budget detail
Budget:
Device Id: blade 1/1
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 301
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes
Device Id: blade 1/3
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 322
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes
Device Id: blade 1/5
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 289
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes
Device Id: blade 1/7
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 288
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes
Device Id: chassis 1
Power Cap (W): 800
Applied Power Cap (W): 800
Admin Priority: Utility
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 756
Power Profiling: No
Method: Unknown
OperMethod: Unknown
OperState: Non Compliant
Psu State: Ok
Power Cap Support: No
Device Id: blade 2/1
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: Utility
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 10
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Unbudgeted
Psu State: Ok
Power Cap Support: Yes
Device Id: blade 2/3
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 279
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes
Device Id: blade 2/5
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 310
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes
Device Id: blade 2/7
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 320
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes
Device Id: chassis 2
Power Cap (W): 800
Applied Power Cap (W): 800
Admin Priority: Utility
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 726
Power Profiling: No
Method: Unknown
OperMethod: Unknown
OperState: Non Compliant
Psu State: Ok
Power Cap Support: No
Device Id: blade 3/1
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 316
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes
Device Id: blade 3/3
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: Utility
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 287
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes
Device Id: blade 3/5
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 280
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes
Device Id: blade 3/7
Power Cap (W): 0
Applied Power Cap (W): 25
Admin Priority: No Cap
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 293
Power Profiling: No
Method: Nodemgr
OperMethod: Static
OperState: Non Compliant
Psu State: Ok
Power Cap Support: Yes
Device Id: chassis 3
Power Cap (W): 800
Applied Power Cap (W): 800
Admin Priority: Utility
Maximum power (W): 0
Minimum power (W): 0
Group: default
Average Usage (W): 724
Power Profiling: No
Method: Unknown
OperMethod: Unknown
OperState: Non Compliant
Psu State: Ok
Power Cap Support: No
Device Id: switch A
Power Cap (W): 335
Applied Power Cap (W): 335
Admin Priority: No Cap
Maximum power (W): 335
Minimum power (W): 335
Group: default
Average Usage (W): 335
Power Profiling: No
Method: Static
OperMethod: Static
OperState: Deployed
Psu State: Ok
Power Cap Support: No
Device Id: switch B
Power Cap (W): 335
Applied Power Cap (W): 335
Admin Priority: No Cap
Maximum power (W): 335
Minimum power (W): 335
Group: default
Average Usage (W): 335
Power Profiling: No
Method: Static
OperMethod: Static
OperState: Deployed
Psu State: Ok
Power Cap Support: No
ucs-A /chassis #
ucs- A# connect iom 1
Attaching to FEX 1 ...
To exit type 'exit', to abort type '$.'
Bad terminal type: "dumb". Will assume vt100.
fex-1# show platform software cmcctrl power config
Redundancy policy: Grid
Chassis power budget: 720/800 # committed/peak
Chassis settings:
pwrcap enabled
dynamic rebalancing enabled
Blade 0:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 1:
Presence: ABSENT
Blade 2:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 3:
Presence: ABSENT
Blade 4:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 5:
Presence: ABSENT
Blade 6:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 7:
Presence: ABSENT
fex-1#
fex-1# show platform software cmcctrl dmclient psreadings
Total Input Power consumption: -1
Total Output Power consumption: -1
Power supply: 0
Voltage (IN) : N/A
Voltage (12V) : N/A
Voltage (3V) : N/A
Current (IN) : N/A
Current (12V) : N/A
Current (3V) : N/A
Peak Current (IN) : N/A
Peak Current (12V) : N/A
Peak Current (3V) : N/A
Temperature 0 : N/A
Temperature 1 : N/A
Temperature 2 : N/A
Fan tach0 : N/A
Fan tach1 : N/A
Fan tach2 : N/A
Fan tach3 : N/A
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : N/A
Operating range : N/A
Max Power : N/A
Power supply: 1
Voltage (IN) : N/A
Voltage (12V) : N/A
Voltage (3V) : N/A
Current (IN) : N/A
Current (12V) : N/A
Current (3V) : N/A
Peak Current (IN) : N/A
Peak Current (12V) : N/A
Peak Current (3V) : N/A
Temperature 0 : N/A
Temperature 1 : N/A
Temperature 2 : N/A
Fan tach0 : 0 rpm
Fan tach1 : 0 rpm
Fan tach2 : 0 rpm
Fan tach3 : 0 rpm
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : N/A
Operating range : N/A
Max Power : N/A
Power supply: 2
Voltage (IN) : N/A
Voltage (12V) : N/A
Voltage (3V) : N/A
Current (IN) : N/A
Current (12V) : N/A
Current (3V) : N/A
Peak Current (IN) : N/A
Peak Current (12V) : N/A
Peak Current (3V) : N/A
Temperature 0 : N/A
Temperature 1 : N/A
Temperature 2 : N/A
Fan tach0 : N/A
Fan tach1 : N/A
Fan tach2 : N/A
Fan tach3 : N/A
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : N/A
Operating range : N/A
Max Power : N/A
Power supply: 3
Voltage (IN) : N/A
Voltage (12V) : N/A
Voltage (3V) : N/A
Current (IN) : N/A
Current (12V) : N/A
Current (3V) : N/A
Peak Current (IN) : N/A
Peak Current (12V) : N/A
Peak Current (3V) : N/A
Temperature 0 : N/A
Temperature 1 : N/A
Temperature 2 : N/A
Fan tach0 : 0 rpm
Fan tach1 : 0 rpm
Fan tach2 : 0 rpm
Fan tach3 : 0 rpm
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : N/A
Operating range : N/A
Max Power : N/A
fex-1#
ucs-B# connect iom 1
Attaching to FEX 1 ...
To exit type 'exit', to abort type '$.'
Bad terminal type: "dumb". Will assume vt100.
fex-1#
fex-1#
fex-1# show platform software cmcctrl power config
Redundancy policy: Grid
Chassis power budget: 720/800 # committed/peak
Chassis settings:
pwrcap enabled
dynamic rebalancing enabled
Blade 0:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 1:
Presence: ABSENT
Blade 2:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 3:
Presence: ABSENT
Blade 4:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 5:
Presence: ABSENT
Blade 6:
Presence: PRESENT
Prio: 0
Non compliance action: None
Excursion action: None
Minimum power budget: 25
Max power budget: 25
Peak power budget: 25
Power cap support: Yes
Boot power budget: 25
Blade 7:
Presence: ABSENT
fex-1# show platform software cmcctrl dmclient psreadings
Total Input Power consumption: 2322
Total Output Power consumption: 2188
Power supply: 0
Voltage (IN) : 234 V
Voltage (12V) : 12082 mV
Voltage (3V) : 3367 mV
Current (IN) : 4984 mA
Current (12V) : 90250 mA
Current (3V) : 15 mA
Peak Current (IN) : 5140 mA
Peak Current (12V) : 92718 mA
Peak Current (3V) : 31 mA
Temperature 0 : 26 C
Temperature 1 : 0 C
Temperature 2 : 0 C
Fan tach0 : 5520 rpm
Fan tach1 : 0 rpm
Fan tach2 : 0 rpm
Fan tach3 : 0 rpm
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : 0x30
Operating range : First
Max Power : 2500 W
Power supply: 1
Voltage (IN) : 236 V
Voltage (12V) : N/A
Voltage (3V) : N/A
Current (IN) : N/A
Current (12V) : N/A
Current (3V) : N/A
Peak Current (IN) : N/A
Peak Current (12V) : N/A
Peak Current (3V) : N/A
Temperature 0 : 24 C
Temperature 1 : 0 C
Temperature 2 : 0 C
Fan tach0 : 0 rpm
Fan tach1 : 0 rpm
Fan tach2 : 0 rpm
Fan tach3 : 0 rpm
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : 0x1
Operating range : First
Max Power : 2500 W
Power supply: 2
Voltage (IN) : 232 V
Voltage (12V) : 12070 mV
Voltage (3V) : 3363 mV
Current (IN) : 4984 mA
Current (12V) : 90968 mA
Current (3V) : 0 mA
Peak Current (IN) : 5140 mA
Peak Current (12V) : 93984 mA
Peak Current (3V) : 0 mA
Temperature 0 : 25 C
Temperature 1 : 0 C
Temperature 2 : 0 C
Fan tach0 : 5790 rpm
Fan tach1 : 0 rpm
Fan tach2 : 0 rpm
Fan tach3 : 0 rpm
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : 0x30
Operating range : First
Max Power : 2500 W
Power supply: 3
Voltage (IN) : 238 V
Voltage (12V) : N/A
Voltage (3V) : N/A
Current (IN) : N/A
Current (12V) : N/A
Current (3V) : N/A
Peak Current (IN) : N/A
Peak Current (12V) : N/A
Peak Current (3V) : N/A
Temperature 0 : 25 C
Temperature 1 : 0 C
Temperature 2 : 0 C
Fan tach0 : 0 rpm
Fan tach1 : 0 rpm
Fan tach2 : 0 rpm
Fan tach3 : 0 rpm
ShutDown Events : 0x0
Warning Input Events : 0x0
Warning Output Events : 0x0
Warning Env Events : 0x0
Status Register : 0x1
Operating range : First
Max Power : 2500 W
fex-1#
Thank You,
Dan Laden
06-29-2018 09:02 AM
I have not be able to re-ack the blade. How likely is it to resolve the issue?
10-16-2019 08:08 AM
I have this issue with only M4 blades. The re-acknowledge is the only thing that seems to clear out the error.
09-10-2018 12:03 PM
Seeing this after trying out VMware DPM which uses IPMI to shutdown and start up blades. Running 3.2.2f with B200M4 & M5.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide