- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-25-2019 10:53 AM
Hello,
I got below alert after upgrade the UCS manager from 4.0. 1d to 4.0.4d. Could you please let me know how to resolve this issue. This is critical alert and what is impact of this alert.
Affected object : sys/user-ext
Description : [FSM:FAILED]: user configuration(FSM:sam:dme:AaaUserEpUpdateUserEp). Remote-Invocation-Error: Failed to configure AAA login block on NXOS, SAM coupler version not supported
ID : 55235895
Type : fsm
Cause : fsm-failed
Thanks,
Suresh
Solved! Go to Solution.
- Labels:
-
UCS Manager
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-25-2019 06:55 PM
The mixed versions are likely leading to the error message you are encountering. We do not recommend running UCSM at a different version than the Fabric Interconnects/IOMs nor is it supported. While the system may operate normally, unexpected behavior may occur. UCSM, FI and IOM should all be on the same version when possible.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-25-2019 12:00 PM
Suresh,
Have all the components been upgraded at this point, or is the upgrade still in progress?
I have seen where during the upgrade process critical errors come up due to communication differences between versions.
--
Niko
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-25-2019 06:46 PM
Thanks Niko,
Currently I have upgraded UCS manager only. all other components running with version 4.0.1d not not planned yet to upgrade on 4.0.4d. Is there any impact of this alerts or can I ignore this alerts.
Thanks,
Suresh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-25-2019 06:55 PM
The mixed versions are likely leading to the error message you are encountering. We do not recommend running UCSM at a different version than the Fabric Interconnects/IOMs nor is it supported. While the system may operate normally, unexpected behavior may occur. UCSM, FI and IOM should all be on the same version when possible.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-25-2019 07:19 PM
Hello Austin,
Yes, I am planning to upgrade the rest all firmware of FIs,IOM, Servers in January 2020. because currently don't have any downtime to upgrade till Jan. We have new UCS servers which was not supported to 4.0.1d hence we upgraded UCS manager to 4.0.4d.
Can we run as it is till Jan.
Thanks,
Suresh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-26-2019 05:02 AM
You can run it, but if you have issues and call TAC for support we will ask you to correct the firmware levels in order to troubleshoot. We have not tested running UCSM 4.0.4 with the FI/IOM at 4.0.1. YMMV.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-06-2019 10:06 PM
Now UCSM, FIs and IOMs are running with same version and alerts has been resolved.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-26-2020 01:43 AM
Hi Was Austin,
We are using FW 4.1(1a) and all are in same version. But still we are seeing the same error with Faulty code F999621.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-26-2020 05:10 AM
It is hard to understand what is going on without looking at your environment, but its possible you were trying to make authentication changes that led to this error.
