I have added a new host to my n1kv, but the interface PortChannel3 appears to be in shutdown and I can't bring it up, despite of it is working.
SW-OUT-N1KV# sh int status
[...]
Po3 -- up trunk full 1000 --
[...]
SW-OUT-N1KV# sh port-channel sum
Flags: D - Down P - Up in port-channel (members)
I - Individual H - Hot-standby (LACP only)
s - Suspended r - Module-removed
S - Switched R - Routed
U - Up (port-channel)
--------------------------------------------------------------------------------
Group Port- Type Protocol Member Ports
Channel
--------------------------------------------------------------------------------
1 Po1(SD) Eth NONE Eth3/2(r)
2 Po2(SU) Eth LACP Eth4/5(P) Eth4/6(P)
3 Po3(SU) Eth LACP Eth5/5(P) Eth5/6(P)
4 Po4(SU) Eth LACP Eth4/1(P) Eth4/2(P) Eth4/3(P)
Eth4/4(P)
5 Po5(SD) Eth LACP Eth5/1(D) Eth5/2(D) Eth5/3(D)
Eth5/4(D)
6 Po6(SD) Eth NONE --
SW-OUT-N1KV# sh run int po3
!Command: show running-config interface port-channel3
!Time: Thu Jan 5 18:00:08 2012
version 4.2(1)SV1(4)
interface port-channel3
inherit port-profile SYSTEM-UPLINK
shutdown
When I try to enable it, I get the following error:
SW-OUT-N1KV(config)# int po3
SW-OUT-N1KV(config-if)# no shut
2012 Jan 5 18:00:51 SW-OUT-N1KV %PORT-PROFILE-2-INTERFACE_QUARANTINED: Interface port-channel3 has been quarantined due to Cmd Failure
The "show logging logfile" and "show accounting log" shows nothing.
Any idea why is it happening????
Other outputs,
SW-OUT-N1KV(config-if)# do sh run port-profile SYSTEM-UPLINK
!Command: show running-config port-profile SYSTEM-UPLINK
!Time: Thu Jan 5 18:02:46 2012
version 4.2(1)SV1(4)
port-profile type ethernet SYSTEM-UPLINK
vmware port-group
switchport mode trunk
duplex auto
speed auto
switchport trunk native vlan 666
switchport trunk allowed vlan 2,43-44
cdp enable
channel-group auto mode active
no shutdown
system vlan 2,43-44
state enabled
SW-OUT-N1KV(config-if)# do sh port-prof virt usag
-------------------------------------------------------------------------------
Port Profile Port Adapter Owner
-------------------------------------------------------------------------------
SYSTEM-UPLINK Po1
Po2
Po3
Eth4/5 vmnic4 10.100.100.63
Eth4/6 vmnic5 10.100.100.63
Eth5/5 vmnic4 10.100.100.64
Eth5/6 vmnic5 10.100.100.64
IESE_CONTENIDO Veth9 Net Adapter 1 IESECMPRO
Veth14 Net Adapter 1 IESEAUTOPRO
IESE_BACKEND Veth10 Net Adapter 1 IESEDBINTPRE
Veth11 Net Adapter 1 IESEDBPRO
IESE_PRE_INT Veth3 Net Adapter 1 IESEWEBPRE
Veth4 Net Adapter 1 IESEAPPINT
Veth5 Net Adapter 1 IESEAPPPRE1
Veth6 Net Adapter 1 IESEAPPPRE2
Veth7 Net Adapter 1 IESEAUTOPRE
Veth8 Net Adapter 1 IESECMINTPRE
DATA-UPLINK-100m Po6
SERVICE-CONSOLE Veth1 vmk0 Module 4
Veth2 vmk1 Module 4
Veth12 vmk0 Module 5
Veth13 vmk1 Module 5
DATA-UPLINK-IESE Po4
Po5
Eth4/1 vmnic0 10.100.100.63
Eth4/2 vmnic1 10.100.100.63
Eth4/3 vmnic2 10.100.100.63
Eth4/4 vmnic3 10.100.100.63
Eth5/1 vmnic0 10.100.100.64
Eth5/2 vmnic1 10.100.100.64
Eth5/3 vmnic2 10.100.100.64
Eth5/4 vmnic3 10.100.100.64
