cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
773
Views
0
Helpful
2
Replies

SFP Tx\Rx power counter on IOMs

d.nepochatykh
Level 1
Level 1

Hello,

Is there any way to check Rx\Tx power , voltage counters and so on on IOMs?

I can check the info on the FI ports, but not on the chassi's IOM:

(nxos)# show interface transceiver details 
Ethernet1/1
    transceiver is present
    type is 10Gbase-SR
...  
    nominal bitrate is 10300 MBit/sec
    Link length supported for 50/125um OM2 fiber is 82 m
    Link length supported for 50/125um OM3 fiber is 300 m
    Link length supported for 62.5/125um fiber is 26 m
    cisco id is --
    cisco extended id number is 4

           SFP Detail Diagnostics Information (internal calibration)
  ----------------------------------------------------------------------------
                Current              Alarms                  Warnings
                Measurement     High        Low         High          Low
  ----------------------------------------------------------------------------
  Temperature   44.16 C        75.00 C     -5.00 C     70.00 C        0.00 C
  Voltage        3.24 V         3.63 V      2.97 V      3.46 V        3.13 V
  Current        6.02 mA       10.00 mA     2.59 mA     8.50 mA       3.00 mA
  Tx Power       -2.21 dBm       1.69 dBm  -11.30 dBm   -1.30 dBm     -7.30 dBm
  Rx Power       -3.13 dBm       1.99 dBm  -13.97 dBm   -1.00 dBm     -9.91 dBm
  ----------------------------------------------------------------------------
  Note: ++  high-alarm; +  high-warning; --  low-alarm; -  low-warning
...

I checked some CLI commands in the mode 'connect iom ...', but didn't find anything useful.

2 Replies 2

AFROJ AHMAD
Cisco Employee
Cisco Employee

Hi ,

You can use the below command to check the SFP status on IOM ::

fex-1# show platform software woodside sfp 0 ni1   >>>> NI1 is the NIF (network interface port)
0-NI1 : : SFP (A0) Info:
## SFP Info:
         SFP FP-Port      : 0
         Fcot Num         : 0
         Fcot Type        : Not Found
      SONET      : No  (Bytes 4-5)
      Ethernet   : No  (Byte  6)
      FC         : No  (Bytes 7-10)
## Error: This SFP has no transceiver codes defined.
         SFP Type         : None
         Min/Max Speeds   : [1094792522, 1129271377] Mbps

         >> BASE ID FIELDS <<
         Bytes  Name               Value
         -----  ----               -----
         0      Identifier       : 0x03 (SFP Transceiver)
         1      Ext. Identifier  : 0x04
         2      Connector Type   : 0x21 (Copper Pigtail)
         3-10   Transceiver      : 0x00 0x00 0x00 0x00 0x00 0x04 0x00 0x00
         (4-5)  - SONET ComplCode: 0x00 0x00 (None)
         (6)    - Eth ComplCode  : 0x00 (Reserved)
         (7)    - FC LinkLength  : 0x00 (None)
         (7-8)  - FC TxType      : 0x37 (None)
         (9)    - FC TxMedia     : 0x00 (None )
         (10)   - FC Speed       : 0x00 (None)
         11     Encoding         : 0x00 (Unknown/Unspecified)
         12     BR, Nominal      : 0x67
         13     Reserved         : 0x00
         14     Length(9m)-km    : 0x00
         15     Length(9m)       : 0x00
         16     Length(50m)      : 0x00
         17     Length(62.5)     : 0x00
         18     Length(Copper)   : 0x05
         19     Reserved         : 0x00
         20-35  Vendor Name      : CISCO-MOLEX     
         36     Reserved         : 0x00
         37-39  Vendor OUI       : 0x00 0x09 0x3A (00093a)
         40-55  Vendor PN        : 74752-9047      
         56-59  Vendor Rev       : 0x30 0x37 0x20 0x20 (07  )
         60-62  Reserved         : 0x01 0x00 0x00
         63     CC_BASE          : 0x10

         >> EXTENDED ID FIELDS <<
         Bytes  Name               Value
         -----  ----               -----
         64-65  Options          : 0x00 0x00 (None )
         66     BR, max          : 0x00
         67     BR, min          : 0x00
         68-83  Vendor SN        : MOC14362896     
         84-91  Date Code(Y/M/D) : 2014/09/09
         92-94  Reserved         : NA
         95     CC_EXT           : 0x9D

         >> Base ID Fields - Raw Hex Dump <<
  Word   0          1          2          3       
  00-03: 03042100 | 00000000 | 04000000 | 67000000
  04-07: 00000500 | 43495343 | 4F2D4D4F | 4C455820
  08-11: 20202020 | 0000093A | 37343735 | 322D3930
  12-15: 34372020 | 20202020 | 30372020 | 01000010

         >> Extended ID Fields - Raw Hex Dump <<
  Word   0          1          2          3       
  16-19: 00000000 | 4D4F4331 | 34333632 | 38393620
  20-23: 20202020 | 31343039 | 30392020 | 0000009D
Access=Ok, A0 CC=Ok, Security Check=Ok, A2 CC=Ok

most of the outputs are some coded values not sure how much they are useful to you..

Thanks-

Afroz

****Ratings Encourages Contributors ****

Thanks- Afroz [Do rate the useful post] ****Ratings Encourages Contributors ****

Yeah, I looked here, but didn't find anything useful.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: