When trying to configure NTP servers (using IP addresses) when http'd into UCS C220 servers, received an XML parser error and the NTP server config did not take. Ideas?
When trying to configure NTP servers (using IP addresses) when http'd into UCS C220 servers, received an XML parser error and the NTP server config did not take. Ideas?
Hello guys! How's everybody doing? We recently upgraded our FIs to v2.2(7b) so our environment could receive new B200M4 blades (according to the release notes, that's the suggested version for this hardware). And according to the same release notes ...
Hello everyone,someone know if is able the Cisco UCS CNA M61KR-I Intel Converged Network Adapter to support uncompressed I/O – 2022-6/7?Thanks a lot in advanceRoberto Loiudice
Dear all, we're deploying a new Flexpod system which is composed of Netapp FAS 2554 filler, cisco nexus 5548UP fabric switch and 5108 UCS blade chassis having two 460 series blade servers. but when we connect the nexus 5548UP ports configured to oper...
Hello. We currently have about 12 Cisco UCS C210 M2's in production and about once a week recently have seen a disk with either a "Predictive Failure" or completely failed. Are there any known issues with this model and failing disks? I've seen th...
Hi, I have a cisco ucsc-c220-M3 server and i could not find out the model of its motherboard.Could you please help me to find the same. Thanks in advance, Jesilraj VP
Hi, i have any problem with a C220 M4 Server. I configured the CISCO 12 G SAS MODULAR RAID CONTROLER with one virtual drive in RAID 5 (boot true). After in the bios i enabled [HBA] on the OPROM module But when i launch the installation of WINDOW...
*Model : CISCO UCS C220 M3 Our C220 is configured RAID 0 (1 HDD) volume of LSI Software RAID. Unfortunately, C220 is suddenly reboot in using. After that, LSI Software RAID disk status changed to "READY" from "ONLINE". SO, We updated latest firmwar...
Hi, I have been battling trying to get help from TAC and researching the internet on the upgrade path for our UCS environment, and as a last resort thought I would try a forum post. My environment is a UCS Chassis environment with dual pathing, Fabr...
Hi all, I have a UCS mini with 6324 I/O modules with 5x B200 m3 blades, each running ESXi 6.0. I want to uplink the UCS mini with four cables to four separate switches for traffic, and I wish for each b200 ESXi host to see four separate vmincs, one...
Hi, I need to know the level of redundancy between the servers in the blade If I have Hyper-V cluster on the 8-servers in a chassis. And there are some VMs created on these servers. Then If I shutdown one server. Are the VMs will move automatically ...
Hi Guys, I got this message on my chassis, can you advise what this means and how can it be cleared: sys/chassis-1/blade-2/mgmt./log-SEL-0 capacity is very low.
I have a few B230M2 sitting inside the UCS 5108 chassis. Looking at the UCS Manager in the Server Detail of that server, I found the "Operating Memory Voltage" has the "Low Voltage" value while other servers have the "Regular Voltage" values. I found...
We have a need to be able to receive a promiscuous mode PVLAN from an upstream Catalyst switch into an existing Cisco UCS Mini chassis. The chassis is connected to the switch that has the PVLANs on it and is already trunking "normal" VLANs to the UC...
Hello,I was wondering if someone can explain (as you can see in the attached pic) why IP's in the Management IP Pool have been assigned twice to the same blade...... I have a pool of 18 IP's and they are all assigned. The other chassis will be connec...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-06-2024 10:53 PM | ||
10-03-2024 07:41 PM | ||
10-03-2024 07:39 PM | ||
08-15-2024 11:16 AM | ||
08-15-2024 08:03 AM |