Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About a.manosca
Stats
Member since
07-08-2002
443
Posts
114
Helpful
15
Solutions
02-16-2010
06:59 PM
Giuseppe hi, Thanks for your responses. Would just like to confirm this because currently as per checking the logs from the router, the free memory is 149896320. 143 MB is still free. The BGP is using around 80 MB. In your current setup are you also using a 512MB or 1G? I'm still checking if our current setup could handle the new routes knowing that there is only 143MB free. Router#show process memory | inc Free Processor Pool Total: 453026368 Used: 303130048 Free: 149896320 Fast Pool Total: 131072 Used: 102128 Free: 28944 PID TTY Allocated Freed Holding Getbufs Retbufs Process Router#show ip bgp sum | inc total bytes BGP using 83936716 total bytes of memory Router#show memory free Head Total(b) Used(b) Free(b) Lowest(b) Largest(b) Processor 54FF5DC0 453026368 303132916 149893452 146564252 139047968 Fast 54FD5DC0 131072 102136 28936 28936 28892 Again, thanks for your inputs.
... View more
02-16-2010
01:24 AM
The current setup is using a GRP with an IOS Version 12.0(31)S4. SLOT 2 (RP/LC 2 ): Route Processor MAIN: type 19, 800-2427-02 rev C0 Deviation: 0 HW config: 0x00 SW key: FF-FF-FF PCA: 73-2170-06 rev B0 ver 5 Design Release 1.5 S/N XXXXXXXXX MBUS: MBUS Agent (1) 73-2146-07 rev B0 dev 0 HW version 1.2 S/N XXXXXXXXX Test hist: 0xFF RMA#: FF-FF-FF RMA hist: 0xFF DIAG: Test count: 0xFFFFFFFF Test results: 0xFFFFFFFF FRU: Linecard/Module: GRP-B= Route Memory: MEM-GRP-512= MBUS Agent Software version 1.117 (RAM) (ROM version is 2.67) ROM Monitor version 2.2 Primary clock is CSC 1 Board State is IOS Running ACTIVE (ACTV RP ) Insertion time: 00:01:01 (3y43w ago) DRAM size: 536870912 bytes Is there a particular command that would show me how many memory it is currently using for routes? If a new IPL will be included would it still write new routes or just update the existing routes on the router?
... View more
02-10-2010
06:09 PM
How would I know if the Cisco 12016 Router can still handle the full internet route from a new IPL and if the router can still handle the load? What particular show command should I use to verify that the router is still capable to handle this?
... View more
Labels:
02-04-2010
01:15 AM
Hi, MPLS-Aware NetFlow feature does not seem to be supported still in 12.2(33) SRD and SRD3 on a 7600, regardless of the feature set. Any news if this feature will be supported? Thanks, Ariel
... View more
09-04-2009
12:18 AM
hi sir, does this contribute on me not being able to access the failover pix? Thanks.
... View more
Created by
a.manosca
in Application Networking
in Application Networking
06-26-2009
02:01 AM
06-26-2009
02:01 AM
Here are the configs and the error logs. Please advise..
... View more
Created by
a.manosca
in Application Networking
in Application Networking
06-26-2009
01:53 AM
06-26-2009
01:53 AM
Hi All, We have 2 CSS in redundant VIP. Can somebody explain the meaning of the error message? Also at several times the services on the active CSS will stall and you have to make the standby CSS active in order to make the services run again. Please advise. I can upload the configs. Best regards!
... View more
Labels:
03-19-2009
06:10 PM
You may want to look at your VAM module. Updating it to VAM2+ may resolve it as to what happened to my case.
... View more
02-24-2009
09:10 AM
Hi Team, I saw this URL: http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a00801982ae.shtml This is a sample mGRE config, however can someone provide a plain mGRE config that I can use? Is tunnel protection and IP NHRP mandatory? Our requirement is just spoke to hub communication without spoke-to-spoke communication.
... View more
Labels:
Created by
a.manosca
in Application Networking
in Application Networking
01-07-2009
06:42 PM
01-07-2009
06:42 PM
I connected the cross cable PRIOR to powering up the standby CSS to avoid making both CSS master. Both CSS have the same config EXCEPT: On the primary CSS: ************************** CIRCUIT ************************** circuit VLAN404 ip address 10.128.138.38 255.255.255.0 ip virtual-router 1 priority 200 ip virtual-router 2 priority 200 ip redundant-vip 1 10.128.138.36 ip redundant-vip 2 10.128.138.37 On the secondary CSS (standby): !************************** CIRCUIT ************************** circuit VLAN404 ip address 10.128.138.39 255.255.255.0 ip virtual-router 1 priority 150 ip virtual-router 2 priority 150 ip redundant-vip 1 10.128.138.36 ip redundant-vip 2 10.128.138.37 They were working before the secondary CSS got RMA. Please advise..
... View more
Created by
a.manosca
in Application Networking
in Application Networking
01-07-2009
04:06 AM
01-07-2009
04:06 AM
Hello, I am trying to setup redundancy between 2 CSS11051 loadbalancers on Active/Standby. Whenever I connect them both to the network they both act as Master. They have the same code but varying in flash and feature set. Will redundancy work on this varying items? CSS11050> sh version Version: ap0500105 (5.00 Build 105) Flash (Locked): 3.10 Build 33 Flash (Operational): 5.03 Build 15 Type: PRIMARY Licensed Cmd Set(s): Standard Feature Set CSS11050WC_A# sh ver Version: ap0500105 (5.00 Build 105) Flash (Locked): 5.00 Build 105 Flash (Operational): 5.00 Build 105 Type: PRIMARY Licensed Cmd Set(s): Standard Feature Set Enhanced Feature Set SSH Server
... View more
Labels:
05-21-2008
02:10 AM
I have a router configured as a dhcp server. At the same time, the interface which the user comes in is also configured to relay dhcp request to external DHCP server. But there are times that the client is getting an IP address from the external DHCP server instead from the router. I know that the request is broadcast but shouldn't the fastest reply comes from the router itself and not from the external DHCP server? Thanks.
... View more
Labels:
Created by
a.manosca
in Security Management
in Security Management
11-04-2007
06:39 PM
11-04-2007
06:39 PM
I'm currently using Campus Manager 4.0.3. Topology services have error in dicovering links, some etherchannel links was discovered correctly some are discovered as separate links. For the incorrectly discovered etherchannel links, it created a bus as a connection to the other devices instead of dispalying it as a single link with multiple port in the link attributes. I already trien re-initializing the Ani Database and i also upgraded the CM to 4.0.5. But still no avail. Need help asap. thnaks.
... View more
Labels:
Created by
a.manosca
in Wireless Security and Network Management
in Wireless Security and Network Management
09-27-2006
01:53 AM
09-27-2006
01:53 AM
For some AP 1200's, WLSE sends a "P1 notification... Device was not reachable via SNMP" followed by a "OK notification ... Device was reachable via SNMP" after a few minutes (between 1 and 5 minutes). Current poll interval setting is 5 minutes and frequency is 1. There are no issues with the AP (interfaces and line protocol are UP/UP). Any advise on what could be causing this problem (and any recommended troubleshooting/solution) is greatly appreciated. Thanks in advance. Ariel
... View more
02-16-2010
Giuseppe hi,Thanks for your responses. Would just like to confirm this
because currently as per chec...
02-16-2010
The current setup is using a GRP with an IOS Version 12.0(31)S4.SLOT 2
(RP/LC 2 ): Route Processor M...
02-10-2010
How would I know if the Cisco 12016 Router can still handle the full
internet route from a new IPL a...
02-04-2010
Hi,MPLS-Aware NetFlow feature does not seem to be supported still in
12.2(33) SRD and SRD3 on a 7600...
Created by
a.manosca
in Application Networking
06-26-2009
06-26-2009
Here are the configs and the error logs.Please advise..
Created by
a.manosca
in Application Networking
06-26-2009
06-26-2009
Hi All,We have 2 CSS in redundant VIP. Can somebody explain the meaning
of the error message?Also at...
03-19-2009
You may want to look at your VAM module. Updating it to VAM2+ may
resolve it as to what happened to ...
02-24-2009
Hi Team,I saw this URL:
http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_examp...
Created by
a.manosca
in Application Networking
01-07-2009
01-07-2009
I connected the cross cable PRIOR to powering up the standby CSS to
avoid making both CSS master.Bot...
Created by
a.manosca
in Application Networking
01-07-2009
01-07-2009
Hello,I am trying to setup redundancy between 2 CSS11051 loadbalancers
on Active/Standby. Whenever I...
05-21-2008
I have a router configured as a dhcp server. At the same time, the
interface which the user comes in...
Created by
a.manosca
in Security Management
11-04-2007
11-04-2007
I'm currently using Campus Manager 4.0.3. Topology services have error
in dicovering links, some eth...
Created by
a.manosca
in Wireless Security and Network Management
09-27-2006
09-27-2006
For some AP 1200's, WLSE sends a "P1 notification... Device was
notreachable via SNMP" followed by a...
Public Statistics
| Date Registered | 07-08-2002 07:10 PM |
| Date Last Visited | 01-17-2019 10:27 PM |
| Total Messages Posted | 443 |
| Total Helpful Votes Received | 114 |
Helpful Votes From
