Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About antyeung
08-18-2017
Stats
Member since
08-23-2006
263
Posts
40
Helpful
20
Solutions
04-14-2016
08:09 AM
You may also want to check what your E911 requirements are as well. Normally customers use STN's from the voip location that has the same physical location as the person making the call so that when the PSAP gets the call the proper physical address shows up.
... View more
04-14-2016
07:57 AM
You may need to contact Verizon to check what the concurrent call or burst is configured for the voip location associated w/ the STN. If you are using a STN from a VoIP location that has a limit of 50 calls as an example, all calls that use that particular STN will count against that limit.
... View more
04-14-2016
07:23 AM
You can use a single STN in the diversion header for all sites. But one thing to be aware of is that Verizon may bill all calls w/ this diversion header to the VoIP location associated to the STN.
You may also need to consider whether your environment will have off-net redirects and if there is a requirements to convey the proper redirect # in the diversion header.
... View more
06-26-2014
01:24 PM
Geevarghese, Thanks for your response. So is the callingPartySelection element supposed to be an optional or mandatory field? Thanks, Anthony
... View more
06-23-2014
09:41 AM
I'm writing several methods to add gateways and gateway endpoints and I'm noticing inconsistencies between what are advertised as mandatory and optional fields in the AXL schema versus what I'm experiencing when I post content to the CUCM AXL interface. When I post a "addGatewayEndpointAnalogAccess" method to add an analog endpoint which does not include the <callingPartySelection> element I get an error; <?xml version='1.0' encoding='UTF-8'?><soapenv:Envelope xmlns:soapenv=" http://schemas.xmlsoap.org/soap/envelope/ "><soapenv:Body><soapenv:Fault><faultcode>soapenv:Client</faultcode><faultstring>Cannot insert a null into column (analogaccessport.tkcallingpartyselection).</faultstring><detail><axlError><axlcode>-391</axlcode><axlmessage>Cannot insert a null into column (analogaccessport.tkcallingpartyselection).</axlmessage><request>addGatewayEndpointAnalogAccess</request></axlError></detail></soapenv:Fault></soapenv:Body></soapenv:Envelope> When I include the callingPartySelection element all is fine. When I look at the published schema, I interpret that it's an optional field; Is <callingPartySelection> a mandatory field, or is the AXL schema incorrect? Thanks, Anthony
... View more
Labels:
06-10-2014
08:11 AM
Adrienne, Thanks for looking into this and identifying the issue. Please do. Is there a DDTS that I can track for this? Thanks, Anthony
... View more
06-09-2014
08:55 AM
Adrienne, CUCM 8.6.2.23900-10 AXL Schema 8.5 Thanks, Anthony POST https://127.0.0.1:65460/axl/ Accept: text/* Authorization: Basic <taken out> Content-Type: text/xml SOAPAction: "CUCM:DB ver=8.5 getGateway" <soapenv:Envelope xmlns:soapenv=" http://schemas.xmlsoap.org/soap/envelope/ " xmlns:ns=" http://www.cisco.com/AXL/API/8.5 "> <soapenv:Header/> <soapenv:Body> <ns:getGateway sequence="?"> <domainName>DCFDHRBLU1-2811</domainName> <returnedTags uuid="?"> <domainName>?</domainName> <description>?</description> <product>?</product> <protocol>?</protocol> <callManagerGroupName uuid="?">?</callManagerGroupName> <units> <unit> <index>?</index> <product>?</product> <subunits> <subunit> <index>?</index> <product>?</product> <beginPort>?</beginPort> </subunit> </subunits> </unit> </units> <vendorConfig> </vendorConfig> </returnedTags> </ns:getGateway> </soapenv:Body> </soapenv:Envelope> HTTP/1.1 200 OK Connection: close Date: Mon, 09 Jun 2014 15:52:38 GMT Server: Content-Length: 1664 Content-Type: text/xml;charset=UTF-8 Client-Date: Mon, 09 Jun 2014 15:52:38 GMT Client-Peer: 127.0.0.1:65460 Client-Response-Num: 1 Client-SSL-Cert-Issuer: /C=US/O=Verizon/OU=Cary/CN=cwma-cucm01-sc1/ST=NC/L=Cary Client-SSL-Cert-Subject: /C=US/O=Verizon/OU=Cary/CN=cwma-cucm01-sc1/ST=NC/L=Cary Client-SSL-Cipher: AES256-SHA Client-SSL-Socket-Class: IO::Socket::SSL Client-SSL-Warning: Peer certificate not verified Set-Cookie: JSESSIONIDSSO=F49AFDB0068B93F37BD9C04E1EE2ABD5; Path=/; Secure Set-Cookie: JSESSIONID=ADCB571A7AAD54BA184C7CC4578284FC; Path=/axl; Secure; HttpOnly <?xml version="1.0" encoding="UTF-8"?> <soapenv:Envelope xmlns:soapenv=" http://schemas.xmlsoap.org/soap/envelope/ "> <soapenv:Body> <ns:getGatewayResponse xmlns:ns=" http://www.cisco.com/AXL/API/8.5 "> <return> <gateway uuid="{0ECE1CD4-3119-C334-2899-9EC33DB53423}"> <domainName>DCFDHRBLU1-2811</domainName> <description>DCFDHRBLU1 451 Blue Hill Ave, Dorchester</description> <product>Cisco 2811</product> <protocol>MGCP</protocol> <callManagerGroupName uuid="{11657476-26D2-F260-2D99-AFF912D1DA85}">BV1-CMG2</callManagerGroupName> <units> <unit> <index>0</index> <product>NM-4VWIC-MBRD</product> <subunits> <subunit> <index>2</index> <product>VIC2-4FXO</product> <beginPort>0</beginPort> </subunit> </subunits> <subunits> <subunit> <index>3</index> <product>VIC-4FXS</product> <beginPort>0</beginPort> </subunit> </subunits> </unit> </units> <vendorConfig> <globalISDNSwitchType>4ESS</globalISDNSwitchType> <switchBack>Graceful</switchBack> <switchBackDelay>10</switchBackDelay> <switchBackSchedule>12:00</switchBackSchedule> <DtmfRelay>NoChange</DtmfRelay> <ModemPassthrough>Enable</ModemPassthrough> <CiscoFaxRelay>Disable</CiscoFaxRelay> <T38FaxRelay>Disable</T38FaxRelay> <rtpPackageCapability>Enable</rtpPackageCapability> <mtPackageCapability>Disable</mtPackageCapability> <resPackageCapability>Disable</resPackageCapability> <prePackageCapability>Enable</prePackageCapability> <sstPackageCapability>Enable</sstPackageCapability> <rtpUnreachableOnOff>Enable</rtpUnreachableOnOff> <rtpUnreachableTimeout>1000</rtpUnreachableTimeout> <rtcpReportInterval>0</rtcpReportInterval> <simpleSdpEnable>Enable</simpleSdpEnable> </vendorConfig> </gateway> </return> </ns:getGatewayResponse> </soapenv:Body> </soapenv:Envelope>
... View more
06-05-2014
04:57 AM
I'm using the getGateway request method to get the gateway configurations from one cluster and then importing the gateway configuration to a target cluster. One thing I noticed is that the getGateway method returns multiple "subunits" elements under the "unit" XML hierarchy when I believe it should only be returning a single "subunits" element based on the schema. Here's an example output from the getGateway response; ' When I believe it should be returning the following "subunits" XML hierarchy; This is causing us a problem because we are not able to "copy/paste" the response output from the getGateway method from one cluster to the addGateway method issued to a target cluster without manipulating the XML. The result of using the response of the getGateway method without manipulating the subunits to comply with the scheme is that we only end up configuring the children configuration within the first "subunits" element. The subsequent "subunits" are ignored. Is this working as designed? Thanks, Anthony
... View more
Labels:
06-04-2014
11:05 PM
I'm not sure if this is what you're looking for but have you tried looking at the WSDL that is included in the AXL Toolkit that can be downloaded from the "Application > Plugins" menu in CUCM? There should be a executeSQLQuery soap request method where you can execute sql queries against the DB. <soapenv:Envelope xmlns:soapenv=" http://schemas.xmlsoap.org/soap/envelope/ " xmlns:ns=" http://www.cisco.com/AXL/API/8.5 "> <soapenv:Header/> <soapenv:Body> <ns:executeSQLQuery sequence="?"> <sql>?</sql> </ns:executeSQLQuery> </soapenv:Body> </soapenv:Envelope> Thanks, Anthony
... View more
11-15-2012
09:32 AM
As far as I know there's no GUID or call ID you can use in an H.245 message. The closest thing you can get is filter based on port number of the H.245 message that's being tunneled on. In slow start the H.245 port will be in the H.225 message and then you can use that to associate what H.245 message is associated w/ the H.225 message exchange. It's been awhile since I looked at these debugs but there may be a debug that show's the port number of the message exchange right before an H.245 is sent or received. It's been awhile so you'll have to play around with the various H.245 debugs to see if there is one- e.g. debug h245 ? debug cch323 ? etc. If there isn't you can maybe come up w/ an ACL or something of the like to print out the ip/port to the console for H.245 messages to give you a reference. Just a thought, which may/may not work. Generally speaking, H.245 messages are horrible on IOS. The messages are so long and they are prone to skip debug lines on a busy gateway. The only times that I really found it useful was when I could collect debugs in a controlled manner when there were not a lot of calls. Either than that I would rather read the H.XXX traces from Callmanager, sniffers, or the other device it's communicating with. If I don't need H.245 messages then I usually get the H225 on the gateway, but even still those can be verbose.
... View more
Created by
antyeung
in IP Telephony and Phones
in IP Telephony and Phones
07-26-2012
12:04 AM
07-26-2012
12:04 AM
CUCM 8.6.1 ATA-187 9.2(1) Currently as it seems CUCM only allows you to configure at most a Maximum Number of Calls of 2 under the line configuration for an ATA-187. Is there any way to increase this number greated than 2? You run into a problem if you want to configure the line for a fxs port on the ATA-187 to be a shared line. If it's a shared line with two phones (e.g. FXS port 1 and port 2 on the ATA) you lose call waiting and the ability to handle more than one call on a phone since you would want to configured the busy trigger as 1 for both. If it's a shared line with three phones (e.g. FXS port 1 and 2 and an IP phone) you can run into the situation that a port on the ATA would be unusable if the other port on the ATA is active along with the other shared line on the IP Phone is active.
... View more
Labels:
Created by
antyeung
in IP Telephony and Phones
in IP Telephony and Phones
07-11-2012
02:35 AM
07-11-2012
02:35 AM
From the Cisco documentation the 69xx model phones should now support multiple calls per line appearance starting with 9.2(1) firmware for SIP. RN 9.2.1 - Multiple Calls per Line Appearance http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/6921_6941_6961/firmware/9_2_1/english/release/notes/6921_921_sip.html#wp200162 69XX Admin Guide for CUCM 8.6 - Multiple Calls Per Line appearance http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/6921_6941_6961/8_6/english/admin_guide/6921usr.html#wpmkr1096048 However, I'm still not able to change the busy trigger under the line configuration for a 69xx phone configured for SIP. The fields are editble if the 69xx was configured for SCCP. Does anyone have any suggestion at what to look at to increase the busy trigger for the 69xx phones when running SIP?
... View more
Labels:
04-29-2011
12:07 PM
Can you try adding this to your GK2 configurations- gatekeeper zone local GK2 R2.com 10.200.78.3 zone remote GK1 R1.com 10.200.78.2 1719 zone remote GK3 R3.com 10.200.34.4 1719 zone remote dummyGK dummygk.com 1.1.1.1 1719 zone prefix GK1 1... zone prefix GK3 5... zone prefix dummyGK 5... lrq forward-queries no shutdown
... View more
04-28-2011
06:03 AM
Nothing really stares out at me. I can't recall if there's a CLI command where you can control the ISDN call leg of sending the "Connected Number" in the ISDN connect. What type of signaling protocol is being used on the other call leg, H.323? Do you know if the device that the Cisco gateway is peering with can remove the "Connected Number" IE?
... View more
Created by
antyeung
in IP Telephony and Phones
in IP Telephony and Phones
04-27-2011
07:15 AM
04-27-2011
07:15 AM
I suppose you can by changing the PI sent in the H225 Alerting to PI=8. But even if you do that I'm not sure if the Cisco gateway (CME in this case) would play inband ringback since technically there's no DSP in the call flow to play the ringback. But that's just my guess since I haven't tested this before.
... View more
04-14-2016
You may also want to check what your E911 requirements are as well.
Normally customers use STN's fro...
04-14-2016
You may need to contact Verizon to check what the concurrent call or
burst is configured for the voi...
04-14-2016
You can use a single STN in the diversion header for all sites. But one
thing to be aware of is that...
06-26-2014
Geevarghese,Thanks for your response.So is the callingPartySelection
element supposed to be an optio...
06-23-2014
I'm writing several methods to add gateways and gateway endpoints and
I'm noticing inconsistencies b...
Created by
antyeung
in Management
06-10-2014
06-10-2014
Adrienne,Thanks for looking into this and identifying the issue. Please
do. Is there a DDTS that I c...
Created by
antyeung
in Management
06-09-2014
06-09-2014
Adrienne,CUCM 8.6.2.23900-10AXL Schema 8.5Thanks,AnthonyPOST
https://127.0.0.1:65460/axl/Accept: tex...
06-05-2014
I'm using the getGateway request method to get the gateway
configurations from one cluster and then ...
Created by
antyeung
in Management
06-04-2014
06-04-2014
I'm not sure if this is what you're looking for but have you tried
looking at the WSDL that is inclu...
11-15-2012
As far as I know there's no GUID or call ID you can use in an H.245
message. The closest thing you c...
07-26-2012
CUCM 8.6.1ATA-187 9.2(1)Currently as it seems CUCM only allows you to
configure at most a Maximum Nu...
Created by
antyeung
in IP Telephony and Phones
07-11-2012
07-11-2012
From the Cisco documentation the 69xx model phones should now support
multiple calls per line appear...
04-29-2011
Can you try adding this to your GK2 configurations-gatekeeper zone local
GK2 R2.com 10.200.78.3 zone...
04-28-2011
Nothing really stares out at me. I can't recall if there's a CLI command
where you can control the I...
Created by
antyeung
in IP Telephony and Phones
04-27-2011
04-27-2011
I suppose you can by changing the PI sent in the H225 Alerting to PI=8.
But even if you do that I'm ...
Public Statistics
| Date Registered | 08-23-2006 12:13 AM |
| Date Last Visited | 08-18-2017 03:53 AM |
| Total Messages Posted | 263 |
| Total Helpful Votes Received | 40 |
Helpful Votes From
