Hi Ciscomates, I'm trying to enable websense filtering in a 2921 but "ip urlfilter server" command is not available, this is my setup, CISCO2921/K9 C2900 Software (C2900-UNIVERSALK9-M), Version 15.4(3)M3 ------------------------------------------------------------------------ Technology Technology-package Technology-package Current Type Next reboot ------------------------------------------------------------------------ ipbase ipbasek9 Permanent ipbasek9 security securityk9 Permanent securityk9 uc None None None data None None None NtwkEss None None None CollabPro None None None When I try to configure url filter I have some commands but not one for server, yourname(config)#ip urlfilter ? alert      Enable alerts allow-mode               Turn on/off allow-mode audit-trail                    Enable logging of URL information at router cache                  Specify size of the cache and timeout value of cache                            entries exclusive-domain                          Specify the exclusive domain name max-request                       Specify maximum number of pending request max-resp-pak                          Specify the number of http responses that can be buffered source-interface                        Specify source interface truncate                          Truncate url <cr> Any ideas? ... View more

Hi ciscomates! I am trying to set a policy for a EVC but I can't match traffic with access-list. This is my config, class-map match-any c1  match access-group name MATCH ! policy-map SETCOS  class c1    set cos 2  class class-default   set cos 7 ! interface GigabitEthernet3/3/4  no ip address  negotiation auto  service instance 6 ethernet   encapsulation dot1q 21   rewrite ingress tag pop 1 symmetric   service-policy output SETCOS   bridge-domain 7 split-horizon ! interface GigabitEthernet6/2 ip address 192.168.254.105 255.255.255.0 media-type rj45 ! interface Vlan7 ip address 192.168.3.1 255.255.255.0 ! ip access-list extended MATCH permit ip host 192.168.254.1 any ! ip route 0.0.0.0 0.0.0.0 192.168.254.1 With this configuration, all my traffic go out EVC with CoS 7 that is the default class, packects to 192.168.254.1 included. If I configure "permit ip any any" under access-list, then all my traffic is being marked with CoS 2. Why this happens? Maybe is not IP traffic? Any ideas? Thanks in advance! ... View more

Hi Ciscomates! I'm trying to set up a PPPoE server in a cisco 7606 to connect PPPoE clients into service instances but I don't know if it's possible. I have a CISCO7606-S SUP7203B + SIP-400 + SPA-5X1GE-V2 with IOS 12.2(33)SRC6 That is part of my config: interface Loopback1 ip address 1.1.1.1 255.255.255.255 ! bba-group pppoe test virtual-template 13 ! interface GigabitEthernet3/3/4 no ip address negotiation auto service instance 6 ethernet encapsulation dot1q 21 rewrite ingress tag pop 1 symmetric bridge-domain 21 split-horizon ! service instance 7 ethernet encapsulation dot1q 22 rewrite ingress tag pop 1 symmetric bridge-domain 21 split-horizon ! ! interface Virtual-Template13 ip unnumbered Loopback1 no ip redirects no ip unreachables ip accounting access-violations ppp authentication pap ! I can't configure  "pppoe enable group test" to enable pppoe server under service instance and if I configure it under physical interface doesn't work. If I set another interface for bridge traffic to another PPPoE server it's works, like this, interface GigabitEthernet3/3/3 no ip address negotiation auto service instance 6 ethernet encapsulation dot1q 7 rewrite ingress tag pop 1 symmetric bridge-domain 21 ! ! But I would like to finish PPPoE sessions in the same router that service instance are. Some ideas? Regards. ... View more

Hi ciscomates! I have a doubt about licence performance into 4451-X, What is the meaning of 1 Gbps performance? I think that the maximun throughput that I can achive in total, adding each interface throughput. In example, If I have a router for routing between two networks I can only reach 500 Mbps per interface. Or, If I need to route three networks I only can reach 1 Gbps in total, ( 250 Mbps in two interfaces plus 500 in the third one) Am I correct? Thank you in advance. ... View more

Hi all!   Is possible to config VPDN in SUP720-3B for a 7606-S router?   Thanks in advance.   Regards. ... View more

Hi all!   I would like to know if some configuration is possible under some hardware setup before buy it. Looking in cisco.com is not enought because all is very general. Maybe some of you have experience or know if it's possible. I have a CISCO7606-S with WS-SUP32-GE-3B.   I know that for VLAN Stacking I need a SIP-400 with SPA-5X1GE-V2 (I think SPA-5X1GE is not supported in SIP-400), but I would like pppoe service, l2tp tunnels and vpdn. By default with my CISCO7606-S with WS-SUP32-GE-3B is not possible to config vpdn for l2tp tunnels, but, if I install SIP-400 with SPA-5X1GE-V2, is possible to config vpdn and l2tp?   Thank you in advance.   Regards ... View more

Hi all!   I would like to know if some configuration is possible under some hardware setup before buy it. Looking in cisco.com is not enought because all is very general. Maybe some of you have experience or know if it's possible. I have a CISCO7606-S with WS-SUP32-GE-3B.   I know that for VLAN Stacking I need a SIP-400 with SPA-5X1GE-V2 (I think SPA-5X1GE is not supported in SIP-400), but I would like pppoe service, l2tp tunnels and vpdn. By default with my CISCO7606-S with WS-SUP32-GE-3B is not possible to config vpdn for l2tp tunnels, but, if I install SIP-400 with SPA-5X1GE-V2, is possible to config vpdn and l2tp?   Thank you in advance.   Regards ... View more

Hi all!   I am looking for a way to set a value of CoS to a inner VLAN when I use staked VLANs. I try to use policy-map but only can mark CoS in outer VLAN. My config, 7206VXR (NPE-G2) 12.4(15)T16 class-map match-all test_cos  match access-group name marca_cos_5 ! policy-map test  class test_cos   set cos 5 ip access-list extended marca_cos_5  permit ip any 10.20.1.0 0.0.0.255 interface GigabitEthernet0/3.103024  encapsulation dot1Q 1032 second-dot1q 4  ip unnumbered Loopback3  service-policy output test   And this is a part of a tcpdump with the policy enabled,  ethertype 802.1Q (0x8100), length 106: vlan 1032, p  5 , ethertype 802.1Q, vlan 4, p 0, ethertype IPv4,   I have the CoS in the outer VLAN but I don't have in the inner one.   Are there a way to set mark in the inner vlan? Somebody has any idea?   Thanks in advance ... View more