About 00u1ab28axbOOzhqE5d7

00u1ab28axbOOzhqE5d7 · 11-17-2025

Cisco blades has a vKVM-Mapped vDVD1.22 boot option and boots to some sort of isolinux. How do you delete this ISO file/boot option in the bios and where is it saved on the server? All of the media has been wiped? I did a factory reset and scrub thro...

00u1ab28axbOOzhqE5d7 · 05-16-2025

I'm trying to factory reset UCS-FI 6454 using init system in switch boot but the loader look like it is some sort of security boot and the loader says "Trying to read config file /boot/grub/menu and I can't type anything and it boots on its own and i...

00u1ab28axbOOzhqE5d7 · 09-23-2024

I have a asa5500x-ssd120 SSD from an ASA5500-X that is opal locked. It is a micron drive. I saw some commands to revert revert or remove the psid for the 3100 Series if I'm not mistaken but those commands are only for that series. There are some raid...

00u1ab28axbOOzhqE5d7 · 12-12-2023

Looking for a way to delete all the emmc partitions on the ie3300. There is an emgy0: partition that has the emergeny install image on that i want deleted. I was to delete everything from this device including the other partitions like the emgy1: if ...

00u1ab28axbOOzhqE5d7 · 10-30-2023

The guide for the 8500 states the factory-reset all command takes backup of existing configuration, and then resets the router to an earlier, fully functional state. My first question is why do they call it a factory reset if the running configuratio...

00u1ab28axbOOzhqE5d7 · 01-09-2026

1-link

00u1ab28axbOOzhqE5d7 · 12-04-2025

Correct. On a side note was only trying to connect one interconnect because all i need to do is power on blades and factory reset them, rinse and repeat. I went ahead and try connecting one interconnect to each IOM with two fiber cables going to each...

00u1ab28axbOOzhqE5d7 · 12-01-2025

Having the same issue. This is my setup. 6454 (with version 4.3.6c if I'm not mistake) with one SFP 10/25G-csr-s one blue fiber cable connected to UCS-IOM-2408 using a SFP 10/25G-csr-s which is in a UCSB-5108-AC2. On a side note, I am using port 1 ...

00u1ab28axbOOzhqE5d7 · 10-13-2025

I copied the System, Kickstart, Image and nuovo files from the switch via tftp. All I'm trying to do is factory reset using the init system command and reusing the 4 files. Is there a way to do it or do you have to use the bundle bin file? I don't ha...

00u1ab28axbOOzhqE5d7 · 05-16-2025

Disregard. I noticed the firmware can be downloaded without a service contract so there should be no issues. Normally an agreement is needed. Just remove the drive and erase it and then follow this. https://www.cisco.com/c/en/us/support/docs/servers-...

Member Since	‎07-21-2021 05:32 AM
Date Last Visited	‎01-14-2026 12:56 AM
Posts	37
Total Helpful Votes Received	2

User Statistics

User Activity

Cisco blade delete vKVM-Mapped vDvD1.22 boot option

UCS-FI 6454 secure boot

asa5500x-ssd120 psid revert

ie3300 remove emergency backup

C8500 factory-reset

Re: Fabric Interconnect Gen 4 6454 unable to discover Chassis 5108 wit

Re: Fabric Interconnect Gen 4 6454 unable to discover Chassis 5108 wit

Re: Fabric Interconnect Gen 4 6454 unable to discover Chassis 5108 wit

Re: Perform a Complete Reimage for FXOS in Firepower 4100 and 9300 Ser

Re: UCS-FI 6454 secure boot