I have a Cisco ASA running the newest code. We configured the WebVPN to run on the outside interface and it works fine. Our internal network has several different VLANs which are all ACL off at the core. We have one internal VLAN used for guests and we want the ability to use the WebVPN so they can access the other restricted VLANS that the outside VPN users can. Can I just enable it on the inside interface and enable same-traffic-security command to all the traffic to flow? ... View more

I have about 50+ 3550 switches running several year old IOS. Now in my network I have several vlans. Vlan 1 - Data Vlan 10 - Voice Vlan 100 - switch management. each switch has an IP of 10.0.0.XXX /24 THis is placed on each switches int vlan100 The problem I am having is we use a tool for remote monitoring. We monitor the switch IP and I keep getting switches that " go down". We lose the management IP, we cannot ping or telnet to it. If we reboot the switch it comes back up. Now it is only that IP.  When the switch is not pingable, every other VLAN on that switch works. The end uses/phones do not have an issue. Originally the uplink ports had the following config int <uplinnk> switchport mode dynamic desirable On the other end of the uplink (The core switch) we set switchport mode trunk Now i was reading and found something that said i need to set a native vlan of hte management vlan across all uplinks and this will correct that problem. So i spend most of last week rebooting or telneting to each switch. I added the following command, switchp[ort native vlan 100. So each switch now looks like int <uplinnk> switchport mode dynamic desirable switchport trunk native vlan 100 And the same command was added to the core too. This appears to correct the issue but this AM i find several switches are not responding again. Has anyone seen this? Is this a freaking bug in the IOS? Am i missing a command? ... View more

I am having an issue with my current setup. We have a main location running CAll manager ver - 7.0.2.10000-18. I have 2 remote sites that run 1861 route with SRST. Each remote site has 4 analog lines connected to the router via a FXO ports. The main site has dual PRI connected to its router. Originally everything was configured with MGCP and MOH and calling worked fine. WE ran into an issue where the remote sites wanted caller ID. We called the local carrier and got caller ID enabled. Then I found out that FXO (analog lines) and MGCP do not work together. So I converted each remote site to H323. I built the config and got everything working. CAller ID works perfect. Inbound and outbound dialing is working. But we just noticed MOH isnt working. We no longer get the music. All we get now are the tones (beeps) that indicates that you are on hold. THe setup was originally confuigured for unicast. I assumed that was the reason why it isnt working and I enabled multi cast on the call manager but it still isnt working. CAn someone point me in the right direction or give me som advice? thanks ... View more

Hi I am running call manager 6.14 and we have a third party paging system getting installed. Now it connects to our IPT system via FXS and FXO ports, The paging system is a digital system and has different zones. Now there is an extension for each department but within that department there are zones. Extension to call is 1000 zone 01 = warehouse zone 02 = warehouse offices zone 03 = both So when a call is placed to 1000, its going to the warehouse paging system. When you dial 1000, one sec later you hear dead air and then you need to dial 01 or 02 or 03 depending on who you want to page. My question is, is there a way to setup the system to do this If i call 1000, it rings and connects, then it automatically dials 01 or want ever one i want it to default too. ... View more

Can someone answer this question. How should the cabling of the sups be in this redunent call for ACtive/Passive setup. Also, can someone point me where i can fine some sample configs. ... View more