About danielrattee

danielrattee · 09-25-2023

Hello,XXXXSW-030#show install summary[ Switch 1 2 ] Installed Package(s) Information:State (St): I - Inactive, U - Activated & Uncommitted,C - Activated & Committed, D - Deactivated & Uncommitted-------------------------------------------------------...

danielrattee · 08-23-2023

Hello, I feel like I am going crazy.I have a PLC that is on VLAN 10, and production clients and label printers that are on VLAN 100.Vlan 10 IP range is 172.18.XX.0 rangeVLAN 100 is on 10.68.XX.0 range.C2960 switchGi1/0/38 is connected to a smaller "d...

danielrattee · 07-19-2023

Hello, This question builds off of the following post:https://community.cisco.com/t5/switching/inconsitent-inferior-pvst-bpdu-received-on-vlan-10/td-p/4852991Would moving the MST switch (sw-50) to PVST to match (SW-03) resolve the issues in the linke...

danielrattee · 06-12-2023

Good Morning,Some insight before the question:I have Ruckus APs creating a bridge between a C2960 and C9300 stack. This works, but I am wanting to replace them with Aironet 1830s so that if there is an issue, I can swap the APs out and restore the br...

danielrattee · 05-15-2023

Hello,I've a wireless bridge setup to connect two switches together. Ruckus APs are being used to bridg the core network to a C2960. We recently had an issue where one of the ruckus APs failed, so it has been decided to setup a secondary connection w...

danielrattee · 10-01-2023

Thank you all.It went a lot more smoother than I was thinking it was going to go. Maybe I shouldn't be so pessimistic.install remove inactive did work and I was able to active the newer version

danielrattee · 09-27-2023

Understood.I'll run it the next time I have a production downtime window (should be this weekend), and I'll update this posts with the results.

danielrattee · 09-27-2023

XXXXSW-030#dir flash:coreDirectory of flash:/core/40495 -rw- 1 Sep 27 2023 07:16:23 -04:00 .callhome1956839424 bytes total (0 bytes free)XXXXSW-030#

danielrattee · 09-26-2023

sh bootXXXXSW-030#sh boot---------------------------Switch 1---------------------------Current Boot Variables:BOOT variable does not existBoot Variables on next reload:BOOT variable = flash:packages.conf;Manual Boot = noEnable Break = noBoot Mode = D...

danielrattee · 09-26-2023

more flash:cat9k_lite_iosxe.16.12.08.SPA.confboot rp 0 0 rp_boot cat9k_lite-rpboot.16.12.08.SPA.pkgiso rp 0 0 rp_base cat9k_lite-rpbase.16.12.08.SPA.pkgiso rp 0 0 rp_daemons cat9k_lite-rpbase.16.12.08.SPA.pkgiso rp 0 0 rp_iosd cat9k_lite-rpbase.16.12...

Member Since	‎01-06-2023 06:35 AM
Date Last Visited	‎10-07-2024 10:11 AM
Posts	32
Total Helpful Votes Received	5

User Statistics

User Activity

Upgrading C9200 with .bin INSTALL mode, space questions.

Am I missing something with trunking an interface?

Question about MST and PVST

Inconsitent inferior PVST BPDU received on VLAN 10

SW_MATM-4-MACFLAP_NOTIF: 2 different AP bridges

Re: Upgrading C9200 with .bin INSTALL mode, space questions.

Re: Upgrading C9200 with .bin INSTALL mode, space questions.

Re: Upgrading C9200 with .bin INSTALL mode, space questions.

Re: Upgrading C9200 with .bin INSTALL mode, space questions.

Re: Upgrading C9200 with .bin INSTALL mode, space questions.