For confirmation:
SW-050#show spanning-tree summary
Switch is in mst mode (IEEE Standard)
Root bridge for: MST0
EtherChannel misconfig guard is enabled
Extended system ID is enabled
Portfast Default is enabled
PortFast BPDU Guard Default is enabled
Portfast BPDU Filter Default is disabled
Loopguard Default is enabled
UplinkFast is disabled
BackboneFast is disabled
Configured Pathcost method used is short (Operational value is long)
Name Blocking Listening Learning Forwarding STP Active
---------------------- -------- --------- -------- ---------- ----------
MST0 0 0 0 12 12
---------------------- -------- --------- -------- ---------- ----------
1 mst 0 0 0 12 12
SW-003#show spanning-tree summary
Switch is in rapid-pvst mode
Root bridge for: VLAN0052, VLAN0414, VLAN0600
EtherChannel misconfig guard is enabled
Extended system ID is enabled
Portfast Default is enabled
PortFast BPDU Guard Default is enabled
Portfast BPDU Filter Default is disabled
Loopguard Default is enabled
UplinkFast is disabled
BackboneFast is disabled
Configured Pathcost method used is short
Name Blocking Listening Learning Forwarding STP Active
---------------------- -------- --------- -------- ---------- ----------
VLAN0001 0 0 0 60 60
VLAN0002 0 0 0 9 9
VLAN0010 0 0 0 19 19
VLAN0052 0 0 0 6 6
VLAN0100 0 0 0 60 60
VLAN0101 0 0 0 15 15
VLAN0200 0 0 0 18 18
VLAN0300 0 0 0 3 3
VLAN0350 0 0 0 13 13
VLAN0411 0 0 0 9 9
VLAN0412 0 0 0 9 9
VLAN0414 0 0 0 2 2
VLAN0417 0 0 0 9 9
VLAN0500 0 0 0 19 19
VLAN0600 0 0 0 3 3
VLAN0603 0 0 0 13 13
VLAN0604 0 0 0 13 13
VLAN0810 0 0 0 21 21
VLAN0900 0 0 0 10 10
---------------------- -------- --------- -------- ---------- ----------
19 vlans 0 0 0 311 311
The interfaces that the APs are connected to on sw-3 and sw-50 are native VLAN 10. SO I am assuming you want the priority for VLAN 10 on SW-3
SW-003#show spanning-tree vlan 10 detail
VLAN0010 is executing the rstp compatible Spanning Tree protocol
Bridge Identifier has priority 8192, sysid 10, address acf5.e66e.7b80
Configured hello time 2, max age 20, forward delay 15, transmit hold-count 6
Current root has priority 4106, address c4b3.6a85.d480
Root port is 3049 (Port-channel1), cost of root path is 1
Topology change flag not set, detected flag not set
Number of topology changes 768 last change occurred 18:57:31 ago
from Port-channel1
Times: hold 1, topology change 35, notification 2
hello 2, max age 20, forward delay 15
Timers: hello 0, topology change 0, notification 0, aging 300
Port 17 (TwoGigabitEthernet1/0/17) of VLAN0010 is designated forwarding
Port path cost 19, Port priority 128, Port Identifier 128.17.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.17, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
The port is in the portfast mode by default
Link type is point-to-point by default
Bpdu guard is enabled by default
Loop guard is enabled by default on the port
BPDU: sent 7334011, received 0
Port 19 (TwoGigabitEthernet1/0/19) of VLAN0010 is designated forwarding
Port path cost 19, Port priority 128, Port Identifier 128.19.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.19, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
The port is in the portfast mode by default
Link type is point-to-point by default
Bpdu guard is enabled by default
Loop guard is enabled by default on the port
BPDU: sent 7293760, received 0
Port 53 (TenGigabitEthernet1/1/1) of VLAN0010 is designated forwarding
Port path cost 2, Port priority 128, Port Identifier 128.53.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.53, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
Loop guard is enabled by default on the port
BPDU: sent 8016918, received 1
Port 55 (TenGigabitEthernet1/1/3) of VLAN0010 is designated forwarding
Port path cost 2, Port priority 128, Port Identifier 128.55.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.55, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
Loop guard is enabled by default on the port
BPDU: sent 8016917, received 1
Port 56 (TenGigabitEthernet1/1/4) of VLAN0010 is designated forwarding
Port path cost 2, Port priority 128, Port Identifier 128.56.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.56, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
Loop guard is enabled by default on the port
BPDU: sent 8016925, received 1
Port 57 (TenGigabitEthernet1/1/5) of VLAN0010 is designated forwarding
Port path cost 2, Port priority 128, Port Identifier 128.57.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.57, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
Loop guard is enabled by default on the port
BPDU: sent 921636, received 2
Port 58 (TenGigabitEthernet1/1/6) of VLAN0010 is designated forwarding
Port path cost 2, Port priority 128, Port Identifier 128.58.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.58, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
Loop guard is enabled by default on the port
BPDU: sent 4990525, received 6
Port 59 (TenGigabitEthernet1/1/7) of VLAN0010 is designated forwarding
Port path cost 4, Port priority 128, Port Identifier 128.59.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.59, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
Loop guard is enabled by default on the port
BPDU: sent 8016924, received 2
Port 143 (TenGigabitEthernet2/0/47) of VLAN0010 is designated forwarding
Port path cost 4, Port priority 128, Port Identifier 128.143.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.143, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
Loop guard is enabled by default on the port
BPDU: sent 1979412, received 0
Port 149 (TenGigabitEthernet2/1/1) of VLAN0010 is designated forwarding
Port path cost 2, Port priority 128, Port Identifier 128.149.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.149, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
Loop guard is enabled by default on the port
BPDU: sent 601089, received 0
Port 150 (TenGigabitEthernet2/1/2) of VLAN0010 is designated forwarding
Port path cost 2, Port priority 128, Port Identifier 128.150.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.150, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
Loop guard is enabled by default on the port
BPDU: sent 601089, received 0
Port 195 (TwoGigabitEthernet3/0/3) of VLAN0010 is designated forwarding
Port path cost 4, Port priority 128, Port Identifier 128.195.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.195, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
The port is in the portfast mode by default
Link type is point-to-point by default
Bpdu guard is enabled by default
Loop guard is enabled by default on the port
BPDU: sent 1691305, received 0
Port 198 (TwoGigabitEthernet3/0/6) of VLAN0010 is designated forwarding
Port path cost 19, Port priority 128, Port Identifier 128.198.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.198, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
The port is in the portfast mode by default
Link type is point-to-point by default
Bpdu guard is enabled by default
Loop guard is enabled by default on the port
BPDU: sent 8016197, received 0
Port 203 (TwoGigabitEthernet3/0/11) of VLAN0010 is designated forwarding
Port path cost 4, Port priority 128, Port Identifier 128.203.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.203, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
Loop guard is enabled by default on the port
BPDU: sent 1691364, received 0
Port 216 (TwoGigabitEthernet3/0/24) of VLAN0010 is designated forwarding
Port path cost 19, Port priority 128, Port Identifier 128.216.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.216, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
The port is in the portfast mode by default
Link type is point-to-point by default
Bpdu guard is enabled by default
Loop guard is enabled by default on the port
BPDU: sent 5862542, received 0
Port 218 (TwoGigabitEthernet3/0/26) of VLAN0010 is designated forwarding
Port path cost 19, Port priority 128, Port Identifier 128.218.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.218, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
Loop guard is enabled by default on the port
BPDU: sent 905235, received 5
Port 245 (TenGigabitEthernet3/1/1) of VLAN0010 is designated forwarding
Port path cost 2, Port priority 128, Port Identifier 128.245.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.245, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
Loop guard is enabled by default on the port
BPDU: sent 598394, received 0
Port 246 (TenGigabitEthernet3/1/2) of VLAN0010 is designated forwarding
Port path cost 2, Port priority 128, Port Identifier 128.246.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 8202, address acf5.e66e.7b80
Designated port id is 128.246, designated path cost 1
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
Loop guard is enabled by default on the port
BPDU: sent 598394, received 0
Port 3049 (Port-channel1) of VLAN0010 is root forwarding
Port path cost 1, Port priority 128, Port Identifier 128.3049.
Designated root has priority 4106, address c4b3.6a85.d480
Designated bridge has priority 4106, address c4b3.6a85.d480
Designated port id is 128.2377, designated path cost 0
Timers: message age 16, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
Loop guard is enabled by default on the port
BPDU: sent 314, received 8008262
Should I just disable spanning tree on the interfaces the APs are connected to? I'm trying to wrap my head around this and I am failing to do so.
